Connection; Setting The Number Of The Dmx Channels; And The Start Address; Specifications - IMG STAGE LINE PARL-45SET Bedienungsanleitung

5.2.1 Connection

For DMX connection, 3-pole XLR connections with
the following pin configuration are available:
pin 1 = ground, 2 = DMX-, 3 = DMX+
For the connection, special cables for DMX signal
transmission (e. g. cables of the CDMXN series
from the MONACOR product line) should be used.
For cable lengths exceeding 150 m, the insertion of
a DMX level matching amplifier (e. g. SR-103DMX
from IMG STAGELINE) is recommended.
1) Connect the input DMX IN (8) to the DMX out-
put of the light controller or another DMX-con-
trolled unit.
If the foot remote control (13) is connected,
disconnect it from the controller so that it will not
interfere with the DMX control.
2) Connect the output DMX OUT (9) to the DMX
input of the next DMX unit. Connect the output
of the latter DMX unit to the input of the follow-
ing unit, etc. until all DMX controlled units are
connected in a chain.
3) To prevent interference in signal transmission:
For long cables or for a great number of units
connected in series, terminate the DMX output
of the last DMX unit in the chain with a 120 Ω
resistor (> 0.3 W): Connect an appropriate ter-
minating plug (e. g. DLT-123 from the MONA-
COR product line) to the DMX output jack.

5.2.2 Setting the number of the DMX channels

and the start address

The number of DMX channels depends on the
functions required and, if applicable, also on the
number of the control channels available at the light
controller. In the 15-channel mode, four spotlights
can be separately controlled for colour mixing; in
the 3-channel mode, only a common control is sup-
ported and the start address is preset to 001 (can-
not be changed).
1) To select the mode with 3 DMX channels, press
the button MENU repeatedly until
on the display. Then the brightness of the
colours can only be set via the following DMX
addresses:
001 brightness red
002 brightness green
003 brightness blue
2) To select the mode with 15 DMX channels,
press the button MENU repeatedly until and a
number between 001 and 512 appear on the
display.
14
3) Press the button ENTER so that a dot on the
right of
4) Use the button
address for the first DMX channel; then press
the button ENTER.
For separate control of the DMX units con-
nected to the light controller, each unit requires
a start address of its own. Example: If the first
DMX channel of the PARL-45SET is to be con-
trolled by DMX address 4, set the start address
on the PARL-45SET to 4. The other 14 DMX
channels of the PARL-45 SET will then be auto-
matically assigned to the subsequent ad -
dresses. Examples of different start addresses:
Start
address
1
4
12
20

DMX address assignment of the PARL-45SET
5) Once the start address has been set, the spot-
lights can be operated by means of the DMX
controller (please refer to the table in chapter
6.1 for the DMX functions). When DMX control
signals are received, the dot on the right of on
the display will start flashing.
6

Specifications

Data protocol:
Number of DMX channels: 3 or 15
Light source: . . . . . . . . . . . 3 RGB LEDs for each
Power of each LED: . . . 9 W
Beam angle: . . . . . . . . . 15°
Power supply: . . . . . . . . . . 230 V/ 50 Hz
Power consumption: . . . . . 55 VA max.
appears
Ambient temperature: . . . 0 – 40 °C
Dimensions: . . . . . . . . . . . 900 × 240 × 50 mm
Height of stand: . . . . . . . . . 1.25 – 2.1 m
Weight: . . . . . . . . . . . . . . . 8.7 kg
lights up.
or to set the DMX start
Addresses Next possible
for the start address for the
PARL-45SET subsequent DMX unit
1 – 15
4 – 18
12 – 26
20 – 34
. . . . . . . . . DMX 512
spotlight
(controller with spot-
lights)
(adjustable in 6 steps)
16
19
27
35