Timex TW2T71100 Waterbury Bedienungsanleitung Seite 7

TYPE 4
HOUR HAND
STOPWATCH
MINUTE HAND
STOPWATCH
SECOND HAND
BASIC OPERATIONS
• 6 o'clock eye displays "seconds elapsed" for the chronograph
• 9 o'clock eye displays "minutes elapsed" for the chronograph
• 3 o'clock eye displays the current time in a 24 hour format
TIME
TO SET THE TIME:
NOTE: The stopwatch must be stopped and reset to the zero position prior to
setting the time...
1... Pull the crown out to position B...
2... Rotate the crown either direction until the 24-hour, hour, and minute hands
display the correct time...
3... Push Crown in to position A...
TO ADJUST THE STOPWATCH HANDS TO THE ZERO POSITION:
1... Pull the crown out to position B...
2... Press pusher "A" to move the stopwatch minute and second hands counter
clockwise to the zero position... Press pusher "B" to move the stopwatch
minute and second hands clockwise to the zero position...
3... Push Crown in to position A...
CHRONOGRAPH
THE CHRONOGRAPH IS CAPABLE OF MEASURING:
• Seconds elapsed up to one minute (6 o'clock eye)
• Minutes elapsed up to one hour (9 o'clock eye)
STANDARD CHRONOGRAPH MEASUREMENT
• Press pusher "A" to start timing
• Press pusher "A" to stop timing
• Press pusher "B" to reset the chronograph to the zero position
SPLIT TIME MEASUREMENT
• Press pusher "A" to start timing
• Press pusher "B" to split
• Press pusher "B" to resume timing
• Press pusher "A" to stop timing
• Press pusher "B" to reset the chronograph to the zero position
TYPE 5
24-HOUR TIME
CHRONOGRAPH
MINUTES
HOUR
CHRONOGRAPH
SECONDS
SETTING THE TIME
1... PULL the crown out to the 2nd position "C"...
2... Turn the crown to set hour and minute hands... Make sure that the 24-hour
time is correct...
3... When the crown is pushed back to the normal position "A", second hand
begins to run...
SECOND HAND
PUSHER "A"
MINUTE HAND
CROWN POSITION
A
B
NORMAL POSITION "1"
PUSHER "B"
24-HOUR HAND
SECOND HAND
PUSHER "A"
MINUTE HAND
CROWN POSITION
7
B C
NORMAL POSITION "A"
PUSHER "B"
DATE
SETTING THE DATE
1... PULL the crown out to the 1st position "B"...
2... Turn the crown counter-clockwise to set the date... *If the date is set between
the hours of around 9:00 PM and 1:00 AM, the date may not change on the
following day...
3... After the date has been set, push the crown back to the normal position "A"...
USING THE CHRONOGRAPH
This chronograph is able to measure and display time in 1-second increments
up to maximum of 29 minutes 59 seconds... The chronograph second hand
moves continuously for 30 minutes after starting...
STANDARD CHRONOGRAPH MEASUREMENT:
1... PRESS pusher "A" to start timing...
2... PRESS pusher "A" to stop timing...
3... PRESS pusher "B" to reset...
SPLIT TIME MEASUREMENT:
1... PRESS pusher "A" to start timing...
2... PRESS pusher "B" to split...
3... PRESS pusher "B" to resume timing...
4... PRESS pusher "A" to stop timing...
5... PRESS pusher "B" to reset...
CHRONOGRAPH RESET (INCL. AFTER REPLACING BATTERY)
This procedure should be performed when the chronograph minute hand or
second hand do not return to zero position after the chronograph has been
reset, including after the battery has been replaced...
1... Pull the crown out to the 2nd position "C"...
2... Press pusher "A" or "B" to set the stopwatch hands to the zero position...
The movements of the stopwatch minute hand and the stopwatch second
hand are interlocked... To set the stopwatch minute hand to the zero position,
continue to move the stopwatch second hand until the stopwatch minute
hand reaches the zero position...
3... Once the hands returns to zero position, return the crown to the normal
position...
ELAPSED TIME RING
If your watch is equipped with a rotatable outer ring on the face, with numbers
corresponding to minutes, you can use this Elapsed Time Ring to time an
activity from the start, or to mark the ending time for the duration of an activity...
TO TIME AN ACTIVITY FROM THE START:
Set the Start/Stop triangle at the time (hour or minute) when you start the activity
(As shown on the left in the illustration shown below)... At completion, you can
see how long the activity took...
TO MEASURE THE TIME REMAINING:
Set the triangle to the hour or minute position when you wish to complete the
activity, and check the watch periodically for progress towards that goal...
In the illustration shown on the previous page on the right you can stop when
the minute hand reaches the 20 minutes past the hour position...
6
222-095001-02
ENGLISH