Kärcher KM 70/30 C Bp Bedienungsanleitung Seite 10

Adjusting the push handle
1. Release both star grips.
Illustration C
Star grip
1
Push handle
2
2. Pull the push handle backwards and swivel it into the desired
position.
3. Push the push handle forward and engage.
4. Tighten the star grips.
Installing the side brush
The side brushes are supplied with the device on delivery and
must be attached to the device before the initial startup.
See chapter "Changing the side brushes".
Charging/inserting the battery pack
Charge the battery pack before the initial startup.
Please observe the instructions for charging and operation in the
operating instructions and safety instructions enclosed with the
battery pack and charger.
1. Fold up the cover of the battery pack holder.
Illustration D
Battery pack holder
1
Rechargeable battery pack
2
Cover of battery pack holder
3
2. Insert the charged battery pack into the battery pack compart-
ment, push it in up to the stop and snap it in place.
3. Close the cover of the battery pack holder.
Operation
Selecting the programme
1. Turn the programme switch to the desired programme.
Illustration E
0 - Device is switched off
1
Sweeping
2
Sweep vacuuming
3
Sweeping
ATTENTION
Risk of damage
Packing tapes, wires or similar can damage the sweeping mech-
anism.
Keep packing tapes, wires or similar away from the device.
Note
Adjust the travel speed to the conditions in order to achieve opti-
mum cleaning results.
Empty the waste container at regular intervals.
Lower the side brushes to clean side edges.
Note
A bucket or other container up to a maximum of 5 kg can be
placed on the cover of the dust suction blower.
1. If necessary, secure the container to the cover with a tension-
ing strap. Guide the tensioning strap through the fastening
eyelet.
2. Swing the side brushes up or down depending on the task.
Note
Dust whirled up by the side brushes is not vacuumed. Only
use the side brushes when sweeping the edges.
3. Set the programme switch to sweeping or sweep vacuuming.
Note
Only use the sweep vacuuming programme when the floor is dry.
4. Push the device over the surface to be sweeped.
Setting the contact pressure of the roller brush
1. Pulling out, adjusting and lowering the lever for the contact
pressure of the roller brush.
Illustration F
10
Lever for contact pressure of roller brush
1
5 - highest contact pressure
1 - lowest contact pressure
P - roller brush raised
Note
Higher contact pressure results in higher energy requirements
and shorter operating times.
Note
To park and transport the device, move the lever to the "P" posi-
tion. Roller brush is fully raised and damage to the bristles is
avoided.
Setting the contact pressure of the side brushes
1. Turn the twist grip for the contact pressure of side brushes in
the desired direction.
Illustration G
Twist grip for contact pressure of side brushes
1
+ Increase the contact pressure
- Reduce the contact pressure
1. Press the push handle slightly downward so that the device
lifts up towards the front.
Illustration H
2. Push the device over the coarse dirt with the front part raised.
3. Lower the device again.
Emptying the waste container
WARNING
Risk of injury
The rotating roller brush can cause injuries.
Before removing the waste container, switch off the device and
wait until the roller brush stops rotating.
Note
Empty the waste container outdoors if possible, as dust is re-
leased.
1. Turn the programme selection switch to "0" and wait until the
roller brush stops rotating.
2. Pull and release the filter cleaning handle several times.
3. Unlock the dust suction and swing it upwards.
4. Pull the waste container upwards by the handle and remove it
from the device.
5. Dispose of the waste in accordance with local regulations.
Illustration I
ATTENTION
Risk of damage
Do not bump into objects when emptying the waste container.
If the device will not be used for a long time, carry out the follow-
ing points.
1. Place the device on a level surface.
2. Turn the programme switch to "0".
3. Move the lever for the contact pressure of the roller brush to
position "P".
4. Remove the battery pack.
5. Clean the device inside and out.
6. Park the device in a protected and dry place.
CAUTION
Risk of injury and damage
Be aware of the weight of the device during transportation.
1. Turn the programme switch to "0".
2. Move the lever for the contact pressure to position "P".
3. To load, lift the device by the carrying handles.
4. Secure the device to the wheels with wedges.
5. Secure the device with ropes or lashing straps.
6. When transporting in vehicles, secure the device against slip-
ping and tipping over according to the applicable guidelines.
English
Picking up coarse dirt
Shutting down
Transport