Werbung
Verfügbare Sprachen
Verfügbare Sprachen
EN
SAFETY REGULATIONS
TO BE OBSERVED SCRUPULOUSLY
IMPORTANT – READ CAREFULLY BEFORE USING
THE MACHINE. KEEP FOR FUTURE REFERENCE
A) TRAINING
1) Read the instructions carefully. Become familiar with the con-
trols and the proper use of the machine. Learn how to stop the engine
quickly.
2) Only use the machine for the purpose for which it was designed,
namely hoeing and loosening the ground. Any other usage may be
hazardous and harm persons and/or damage things. Examples of
improper use may include, but are not limited to:
– transporting persons, children or animals on the machine;
– letting oneself be transported by the machine;
– using the machine to tow or push loads;
– use of the machine by more than one person;
– operating the milling cutters on firm surfaces or with gravel or sto-
nes.
3) Never allow children or people unfamiliar with these instructions
to use the machine. Local laws can restrict the minimum age of the
operator.
4) Never use the machine:
– when people, especially children or pets are nearby;
– if the operator has taken medicine or substances that may impair
his ability to react and be attentive.
5) Bear in mind that the operator or user is responsible for accidents
or unexpected events occurring to other people or their property.
B) PRELIMINARY OPERATIONS
1) While working, always wear sturdy footwear and long trousers.
Do not operate the machine when barefoot or wearing open sandals.
2) Thoroughly inspect the entire work area and remove anything that
could be thrown by the machine or damage the rotary tools or engine
(stones, branches, iron wire, bones, etc.).
3) WARNING: DANGER! Petrol is highly flammable.
– store the fuel in suitable containers;
– add fuel using a funnel, only outdoors; never smoke while doing this
and whenever fuel is handled;
– add petrol before starting the engine; never add petrol or remove the
petrol tank cap while the engine is running or when it is hot;
– if you have spilt some petrol, do not attempt to start the engine but
move the machine away from the area of spillage to avoid creating
any source of ignition until the fuel has evaporated and fuel vapours
have dissipated;
– always put the tank and fuel container caps back on and tighten
well;
4) Replace faulty silencers
5) Before use, always inspect generally and in particular to see that
the blade, screws and rotary tools are not worn or damaged. Replace
damaged or worn milling cutters and screws to preserve balance.
6) Before starting work, make sure the guards are fitted correctly.
C) DURING USE
1) Do not operate the engine in a confined space where dangerous
carbon monoxide fumes can develop.
2) Work only in daylight or good artificial light.
3) Make sure you have a steady foothold on slopes.
4) Never run with the machine, always walk.
5) Always work transversally on slopes and never up and down
6) Be extremely carefully when changing directions on slopes.
7) Do not work on land that slopes more than 20°
8) Be extremely careful when you pull the machine toward you.
9) Do not change the engine settings or overspeed the engine.
28
10) Start up the engine carefully according to the instructions, keeping
feet away from the rotary tools.
11) Never place your hands and feet near or under rotating parts.
12) Do not lift or transport the machine when the engine is running.
13) Stop the engine:
– whenever you leave the machine unattended;
– before refuelling;
14) Reduce the throttle setting before stopping the engine. Shut off
the fuel supply when work is done, following the instructions in the
engine manual.
And furthermore:
• Stop the rotary tools if the machine must be inclined, when moving
over surfaces other than grass and when the machine is transported
from or to the work area.
• Never operate the machine with damaged guards.
• Stop the engine and disconnect the spark plug cable:
– before doing anything to the rotary tools;
– before checking, cleaning or working on the machine;
– after striking a foreign object. Inspect the machine for damage
and make repairs before restarting and operating the machine;
– if the machine begins to vibrate abnormally (Immediately look
for the cause of vibration and take it to a Specialised Centre for
necessary inspections).
• When working, always keep a safe distance from the rotary tools,
given by the length of the handle.
D) MAINTENANCE AND STORAGE
1) Keep all nuts and screws tight to be sure the machine is in safe
working condition. Routine maintenance is essential for safety and for
maintaining a high performance level.
2) Do not store the machine with petrol in the tank in an area where
petrol vapours could reach an open flame, a spark or a strong heat
source.
3) Allow the engine to cool before storing the machine in any en-
closure.
4) To reduce fire hazards, keep the engine, silencer, battery com-
partment and petrol storage area free of grass, leaves, or excessive
grease.
5) For safety reasons, never use the machine when it has worn or
damaged parts. Parts must be replaced and not repaired. Use original
spare parts. Parts that are not of the same quality can damage the
equipment and impair your safety.
6) If the fuel tank has to be emptied, this should be done outdoors
once the engine has cooled down.
And furthermore:
• Stop the engine and disconnect the spark plug cable before doing
any maintenance;
• Wear work gloves to dissemble and reassemble rotary tools.
E) TRANSPORTATION AND HANDLING
1) Whenever the machine is to be handled, lifted, transported or
tilted you must:
– stop the engine;
– wear sturdy work gloves;
– grasp the machine at the points that offer a safe grip, taking ac-
count of the weight and its distribution.
use an appropriate number of people for the weight of the machine
and the characteristics of the vehicle or the place where it must be
placed or collected.
2) During transport, fasten the machine securely with cables or
chains.
Werbung
