Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Software Updates & Stop+Go & Current Monitor & Support
11. Software-Updates
The ECoSBoost software can be also updated for the ECoSlink bus,
like any other device. Thus it is possible to upgrade new functions
or remove week points.
An update can only be carried out when the booster is connected
to a command station. Every time you switch on the ECoSBoost,
the command station will check if a latest firmware is available and
will update all the boosters connected automatically. New firmwa-
re for boosters is therefore always an integrated part of the central
software.
During the update the boosters cannot be accessed, the LED sta-
tus shuts off. The status bar of the command station will show an
update symbol.
12. Stop" and "Go" button
If you have at least one or more ECoSBoost devices connected
to your command station, the behaviour of the Stop- and Go-
buttons will change.
After briefly pushing the "Stop" button the command station will
immediately interrupt the track current and all external boosters.
The display shows "Emergency Stop", the red "Stop" button is
lit. Use the "Stop" button in case of danger or when you place or
remove a loco on or from the tracks.
If the boosters are configured to switch off in case of a short circuit
or an overload, the "Stop" button will also blink red.
The "Go" button releases the "Emergency Stop", resp. the short
circuit. The internal and the external boosters are re-activated.
Operation may continue.
If the "Go" button blinks green then at least one ECoSBoost boos-
ter in the system has been shut down due to a short circuit. Howe-
ver, at least one booster remains active. In this operating status all
boosters can be re-activated by pressing the "Go" button.
13. Current monitor of the ECoS/Central Station
The current monitor provides valuable information regarding the
energy demand of your layout. With its assistance you can deter-
mine the actual power consumption of your layout and thus better
plan its power districts.
From ECoS software version 1.1.0 or central station® 2.0.4. you
will find the current monitor in the set-up menu by pressing the
respective symbol:
a) List of all internal boosters in the system
b) Separate display for every ECoSBoost (with triggered short circuit)
c) Display for external DCC or 6017 boosters
d) Present current / maximum current
e) Bar display of weighted average (tendence)
f) Present track voltage in the booster district
g) Present internal temperature of the booster
a)
b)
c)
d)
e)
Figure 14
The current monitor will always offer you an overview over your
layout´s current supply situation. The current monitor also shows
which booster has been switched off due to a short circuit.
14. Support and Assistance
Your model train dealer or hobby shop is your competent partner
for all questions regarding your LokPilot decoder. In fact he is your
competent partner for all questions around model trains.
There are many ways to get in touch with us. For enquiries please
use either email, fax (please provide your fax-no. or email address)
or go to www.esu.eu/en/forum and we will reply within a few
days.
Please call our hotline only in case of complex enquiries that can't
be dealt with by email or fax. The hotline is often very busy and
you may encounter delays. Rather send an email or fax and also
check our website for more information. You will find many hints
under "Support / FAQ" and even feedback from other users that
may help you with your particular question.
Of course we will always assist you; please contact us at:
USA & Canada (English support), please contact:
Phone:
+1 (570) 980-1982
Tuesday & Thursday 8:00am - 4:00pm (EST)
Email:
support@loksound.com
Mail:
ESU LLC
1304 Jordan Ave
Montoursville Pennsylvania 17754, USA
Germany and all other countries, please contact:
Email:
support@esu.eu
Mail:
ESU GmbH & Co. KG
- Technical support -
Edisonallee 29
D-89231 Neu-Ulm
GERMANY
f)
g)
11
Werbung
