ZENEC ZE-RVSC200 Montageanleitung Seite 2

MOUNTING
INSTRUCTIONS
0.4 m
KEY FEATURES
• Compact twin-sensor rear view camera
• Fast-mount click-on system for camera main assembly on mounting plate
• Cam1 sensor with 45° and Cam2 sensor with 100° horizontal view angle
• Manual adjustment of vertical / horizontal image section for Cam1 / Cam2
• IR-LED night-illumination system for Cam2 with dynamic LDR brightness control
• Integrated microphone (Cam2)
• Separable 3-part system cable with 17.0 m main cable length
• Adaptor for factory-installed Waeco main cable supplied with the set
DESCRIPTION:
The ZENEC ZE-RVSC200 twin-lens rear view camera was specially developed for semi- and fully-integrated motorhomes. In the
upper part of the camera body is the so-called Cam1. The main task of this camera is to replace the not available interior mirror.
The camera lens, which is located in the lower part, is called Cam2 and is mainly intended for maneuvering and reversing. Cam2
will record the individually adjustable area of up to 5 meters behind the motorhome. An integrated microphone as well as the IR-
LED night illumination system will support the lower camera (Cam2).
This product is compatible with a variety of 2-DIN A/V aftermarket receivers and models of the ZENEC E>GO line up, featuring
two inputs for reversing cameras and one for microphone.
CAUTION:
Use the included connection cable exclusively. Altering or replacing it will void your warranty.
The camera is water- and dustproof and has been licensed according to the international standard IP69K. However,
vehicle cleaning using high pressure water and steam jet devices may still lead to damage of IP69K rated camera
models by water intrusion. Keep a distance of at least one meter between the water nozzle and the camera housing.
EN
Technical Specifications:
Image device
Cam1 + Cam2:
View angle (horizontal)
Cam1/Cam2:
Lens focal length Cam1/Cam2:
Picture resolution of sensor:
Resolution of video-out signal:
Frame rate:
TV system:
Signal to noise ratio:
Light sensitivity:
Video output:
White balance:
Backlight compensation:
Gamma correction:
Gain control:
Sync system:
Power supply:
Current consumption (@12VDC):
IP protection rating:
Operating temperature:
ZENEC Bohrturmweg 1 CH-5330 Bad Zurzach Switzerland
EU Legal Representative:
ACR S & V GmbH Industriestraße 35 D-79787 Lauchringen Germany
TWIN-SENSOR REAR VIEW CAMERA
0.4 m
17 m
¼" / 6.4 mm Aptina ASX340 AT
CMOS sensor
45° / 100°
f4.2 / f2.0
680 (H) x 512 (V) pixels
> 420 TV lines
60 fi elds/sec.
NTSC / 60 fps
> 48 dB
0.5 Lux/F1.2/50IRE ; Cam 2: 0 Lux IR ON
1.0 Vp-p, 75 ohms CVBS
Auto
Auto
0.45
Auto
Auto
DC 12V
50mA Cam1 + 80 mA Cam2
IP69K
-30°C~+75°C
White
Black
Red
DE Technische Spezifikationen
Bildsensor
Cam1 + Cam2:
Betrachtungswinkel (horizontal)
Cam1/Cam2:
Brennweite Linse von Cam1/Cam2: f4.2 / f2.0
Sensor Bildaufl ösung:
Aufl ösung Video-Ausgangssignal:
Bildwiederholrate:
TV System:
Signal/Rauschabstand:
Lichtempfi ndlichkeit:
Video Ausgang:
Weißabgleich:
Belichtungskompensation:
Gamma Korrektur:
Helligkeitsabgleich:
Synchronisation:
Spannungsversorgung:
Stromverbrauch (@12VDC):
Schutzklasse:
Betriebstemperatur:
ZE-RVSC200
Audio Out (Cam 2)
Video Out (Cam 2)
Video Out (Cam 1)
Camera 1 Power (+12V)
Ground (GND)
Camera 2 Power (+12V)
¼" / 6.4 mm Aptina ASX340 AT
CMOS Sensor
45° / 100°
680 (H) x 512 (V) Pixel
> 420 TV Linien
60 Felder/Sek.
NTSC / 60 fps
> 48 dB
0.5 Lux/F1.2/50IRE; Cam 2: 0 Lux IR ON
1,0 Vp-p, 75 Ohm CVBS
Automatisch
Automatisch
0.45
Automatisch
Automatisch
DC 12V
50mA Cam1 + 80 mA Cam2
IP69K
-30°C~+75°C
Rev. A