ZENEC ZE-RCE3704-2S Montageanleitung

ZENEC
MOUNTING INSTRUC TIONS
MOUNTING INSTRUCTIONS
300 mm
Dometic 6 CAM035 6
WIRING DIAGRAM
WIRING DIAGRAM
Pin out of DOMETIC CAM035 6 pin connectors
ZE-RCE3704-2S MALE
ZE-RCE3704-2S
11.0 m
KEY FEATURES
KEY FEATURES
• Compact high resolution rear view camera for FIAT Ducato III
• Compact high resolution rear view camera for FIAT Ducato Ill
vehicles, incl. Series 8 and other identical type variants
vehicles, incl. Series 8 and other identical type variants
• System design integrating the original Ducato brake light
• System design integrating the original Ducato brake light
retaining the road use homologation*
retaining the road use homologation* I 1
• Cam1 sensor with 50° and Cam2 sensor with 100° horizontal
• Caml sensor with 500 and Cam2 sensor with 1000 horizontal
view angle
view angle
• Manual adjustment of vertical image section of Cam2
• Manual adjustment of vertical image section of Cam2
• IR-LED illumination system with dynamic LDR brightness
• IR-LED illumination system with dynamic LDR brightness
control for Cam2
control for Cam2
• Integrated microphone (Cam2)
• Integrated microphone (Cam2)
• Separable main cable with DOMETIC CAM035 6-pin
• Separable main cable with DOMETIC CAM035 6-pin
connectors, suitable for direct connection with factory routed
connectors, suitable for direct connection with factory routed
DOMETIC main cable in vehicle
DOME TIC main cable in vehicle
• Plastic injection main housing with stainless steel fi xation bolts
• Plastic injection main housing with stainless steel fixation
* 1 The ZE-RCE3704-2S integrates into the original brake light insert of the vehicle.
*IThe ZE-RCE3704-2S integrates into the original brake light insert of the vehicle.
The brake light is not part of the supplied set content.
The brake light is not part of the supplied set content.
COMPATIBLE WITH MODEL TYPE MODEL YEAR
COMPATIBLE WITH MODEL TYPE
MODEL YEAR
Fiat Ducato III 250/251 2006 – 2011
Fiat Ducato Ill 250/251 2006 - 2011
Fiat Ducato III 250/251 2011 – 2014
Fiat Ducato Ill 250/251 2011 - 2014
Fiat Ducato III 250/251 (X290) 2014 – 2021
Fiat Ducato III 250/251 (X290) 2014 - 2021
Fiat Ducato III Series 8 as of 2021
Fiat Ducato III as of 2021
Citroën Jumper II 250/250D/250L as of 2006
Citroän Jumper II 250/250D/250L as of 2006
Peugeot Boxer 250/251 as of 2006
Peugeot Boxer 250/251 as of 2006
Opel Movano Type C as of 2021
Opel Movano Type C as of 2021
A CAUTION:
CAUTION:
Use the included connection cable exclusively. Altering or replacing it will void your warranty.
Use the included connection cable exclusively. Altering
The camera is water- and dustproof and has been licensed according to the international standard IP68. However, vehicle clean-
The camera is water- and dustproof and has been licensed according to the international standard IP68. However, vehicle clean-
ing using high pressure water and steam jet devices may still lead to damage of IP68 rated camera models by water intrusion.
ing using high pressure water and steam jet devices may still lead to damage
Keep a distance of at least one meter between the water nozzle and the camera housing.
Keep a distance of at least one meter between the water nozzle and the camera housing.
E13 IOR-06/01 16320
ZENEC by ACR AG ∙ Bohrturmweg 1 ∙ CH-5330 Bad Zurzach ∙ Switzerland, EU Legal Representative: ACR S & V GmbH ∙ Industriestr. 35 ∙ D-79787 Lauchringen ∙ Germany ∙ www.zenec.com
ZENEC by ACR AG Bohrturmweg 1 - CH-5330 Bad Zurzach Switzerland, EU Legal Representative:
ZE-RCE3704-2S ZE-RCE3704-2S
ZE-RCE3704-2S
RE AR VIE W C AMER A FOR FIAT DUC ATO
REAR VIEW CAMERA FOR
11m I (X) mm
DometicCAM035 6 pin
Dometic CAM035 6 pin
FEMALE
0)
+12VCAM2
2
CAM 1 signal +
MIC signal +
30 cm
3.5 mm
+12VCAM1
jack
GND
6
CAM 2 signal +
TECHNICAL SPECIFICATIONS
TECHNICAL SPECIFICATIONS
Image device Cam1 / Cam2: Pixelplus PC3089
Image device Caml / Cam2: Pixelplus PC3089
Image sensor type: 1/3" / 8.5 mm CMOS sensor
Image sensor type: 1/3" / 8.5 mm
TV system: NTSC / 60 fps
TV system: NTSC / 60 fps
View angle Cam1 / Cam2: 50° / 100° horizontal
View angle Caml / Cam2: 500 / 1000 horizontal
Total sensor-die based pixel matrix: 756 (H) x 504 (V) pixels
Total sensor-die based pixel matrix: 756 (H) x 504 (V) pixels
Image relevant pixel matrix: 720 (H) x 480 (V) pixels
Image relevant pixel matrix: 720 (H) x 480 (V) pixels
Lens focal length: f4.2 / f2.0
Lens focal length: f4.2 / f2.O
Frame rate: 60 fi elds/sec.
Frame rate: 60 fields/sec.
Signal to noise ratio: >47 dB
Signal to noise ratio: dB
Dynamic contrast: >62 dB
Dynamic contrast: dB
Light sensitivity: 0.5 Lux/F1.2/50IRE – 0 Lux with
Light sensitivity: 0.5 Lux/F1.2/501RE
IR-LED ON
IR-LED ON
Video output: 1.0 ±0.2 Vp-p, 75 Ω, CVBS
Video output: 1.0±0.2 vp-p, 75 Q, CVBS
bolts
White balance: Auto
White balance: Auto
Backlight compensation: Auto
Backlight compensation: Auto
Gamma correction: 0.45
Gamma correction: 0.45
Gain control: Auto
Gain control: Auto
Sync system: Auto
Sync system: Auto
Power supply: 12 DCV (6 V – 16 V)
Power supply: 12 DCV (6 V- 16 V)
Current consumption (@12 V DC): 80 mA ±10 mA total for
Current consumption (@12 V DC): 80 mA ±10 mA total
Cam1 + Cam2
Caml + Cam2
IP protection rating: IP68
IP protection rating: IP68
Operating temperature: -20° C ~ +70° C
Operating temperature: -200 c +700
or replacing it will void your warranty.
of IP68 rated camera models by water intrusion.
ACR S & V GmbH - Industriestr 35 D-79787 Lauchringen
FIAT DUCATO
INSTALLATION
INSTALLATION
1
1 50 mm
Gut 2
G,VD
200 mm
1. Unscrew and remove both Philips head screws.
I. Unscrew and remove both Philips head screws.
Retain the screws for later remounting of the brake light
Retain the screws for later remounting of the brake light
reflector.
reflector.
Original Connection
2
yellow RCA
2
red RCA
white
black
white RCA
2. Pull the brake light reflector unit out of its mounting
2. Pull the brake light reflector
slot. Disconnect the white power supply system
slot. Disconnect the white power supply system
CMOS sensor connector plug of the vehicle.
connector plug of the vehicle.
3
- 0 Lux with
3. Screw in and tighten the stainless steel mounting
3. Screw in and tighten the stainless
bolts by hand (5Nm). Use a dab of Loctite, if possible.
bolts by hand (5Nm). Use a dab of Loctite, if possible.
4
for
c
MIC ----->
CAM 2
CAM 1
4. Route the main cable from the naviceiver in the vehicle
4. Route the main
cockpit / dashboard to the brake light opening in the up-
cockpit / dashboard
per rear section of the vehicle. For power and RCA video
per rear section of the vehicle. For power and RCA video
signal, the ZENEC Infotainer offers a direct system "con-
signal, the ZENEC Infotainer offers a direct system "con-
nector block E" which offers switched 300mA power out's
nector block E" which offers switched 300mA power out's
(see installation guide of ZENEC head unit).
(see installation guide of ZENEC head unit).
PAP
Germany www.zenec.com
5
5. Connect the 6PIN connector plug of the cam sensor
5. Connect the 6PIN connector plug of the cam sensor
side with its counterpart of the cable coming from the
side with its counterpart
vehicle. Use self-adhesive tape to physically secure the
vehicle.
connectors as well as to prevent water from entering the
connectors as well as to prevent water from entering the
connectors.
connectors.
6
6
6. Plug in the white power supply system connector
unit out of its mounting 6. Plug in the white power supply system connector
plug in the socket of the brake light reflector housing
plug in the socket of the brake light reflector housing
backside.
backside.
7
7. Align the cam housing / reflector assembly over the
steel mounting 7. Align the cam housing / reflector
mounting location. Fix the assembly with the original
mounting
Philips head screws.
Philips head screws.
8. (no picture)
8. (no picture)
Connect the wires and connectors of the cam main har-
Connect
ness to the HU in the dashboard. Perform a cam function
ness
Reverse
test. Also check for proper function of the 3
test. Also check for proper
Speed In
IR In
ext. Mic
Power 2 300mA
2 scan-A
Power 1 300mA
> Power 1
9
GNO
Audio In
cvas In 2
E
CVES In 1
cable from the naviceiver in the vehicle
to the brake light opening In the up-
9. Cam2 pointing down is a vertically swiveling design,
9. Cam2 pointing down is a vertically
allowing to align the desired image section shown on the
allowing to align the desired image section shown on the
HU manually. Align cam2 for best field of view. Installation
HU manually. Align cam2 for best field of view. Installation
and cam setup is completed.
and cam setup is completed.
ZE-RCE3704-2S ZE-RCE3704-2S
ZE-RCE8704-2S
RE AR VIE W C AMER A FOR FIAT DUC ATO
REAR VIEW CAMERA FOR FIAT DUCATO
of the cable coming from the
Use self-adhesive tape to physically secure the
assembly over the
location. Fix the assembly With the original
the wires and connectors of the cam main har-
to the HU in the dashboard. Perform a cam function
brake light.
rd
function of the brake light.
swiveling design,