Hendi 230695 Benutzerhandbuch Seite 11

Internal wire terminal for
38
the magnetic switch
39 PCB assembly
40 Screws for fixing PCB assembly
41 Sound absorption cotton
Preparation before use
• Remove all protective packaging and wrapping.
• Check that the device is in good condition and with all
accessories. In case of incomplete or damaged delivery,
please contact the supplier immediately. In this case, do not
use the device.
• Clean the accessories and the appliance before use (See
==> Cleaning & Maintenance).
• Make sure the appliance is completely dry.
• Place the appliance on a horizontal, stable and heat resist-
ant surface that is safe against water splashes.
• Keep the packaging if you intend to store your appliance in
the future.
• Keep the user manual for future reference.
NOTE! Due to manufacturing residues, the appliance may
emit a light odor during the first few uses. This is normal and
does not indicate any defect or hazard. Make sure the appli-
ance is well ventilated.
Operating instructions
• IMPORTANT! This machine has a specially designed safety
feature: Protective cover.
The machine can only operate when the protective cover is
closed and the jug is installed properly on the motor base.
• NOTE! For safety reason, the machine can only start to op-
erate with the jug installed properly on the motor base and
the protective over is closed properly.
• Check if the machine is at the STANDBY mode.
• Unplug the machine and open the protective cover, take out
the jug from the motor base.
• Pour all the ingredients into the jug and close it with the jug
lid and place the cover cap correctly in place.
• Place the whole jug onto the motor base & close the pro-
tective cover.
• Connect the power plug to a suitable electrical power supply
socket.
• Press the power switch once to enter STANDBY mode.
Then, press the power switch again to switch ON the ma-
chine and 20 (Note: Default speed is 20) will be shown on the
digital control display or select a suitable speed by pressing
the desired speed control button: / / will then be shown
on the digital control display correspondingly.
• Select the time for operation (30s / 45s / 90s) by pressing the
timer button. Remaining time will be shown on the digital
control display. Once the set time is elapsed, the machine
will stop operation and go to STANDBY mode.
• After use, always press the power switch to STANDNY mode
and disconnect the plug from the electrical socket.
NOTE! The digital control panel has 2 level for brightness.
When you press, it will be brighter. Otherwise, it will remain in
minimum brightness mode.
Speed selected
1
Low speed ( )
Speed
1
control
Medium ( ) and
button
2
high ( ) speed
1
Pulse function
Remarks:
1. For the best results when blending solid foodstuffs, only
add small portions in succession, not all ingredients at the
same time.
2. Always start with lower speed (
switch to the high speed ( ) or to the "Pulse" function, so
as not to jam the blade assembly.
3. Do not use this machine to blend hard foodstuff, such as
nuts.
4. Do not fill liquids above the MAX. mark of the jug.
5. Liquids to be blend should be at or below room temper-
ature. If you are going to blend warm liquids, ensure that
the jug lid is correctly in place and use low speed for pro-
cessing. Risk of burns and be careful.
6. Avoid long period of operation due to the loud noise that
may hurt the hearing.
Cleaning & maintenance
• ATTENTION! Always disconnect the appliance from the
power supply and cool down before storage, cleaning &
maintenance.
• Do not use water jet or steam cleaner for cleaning and do
not push the appliance under the water as the parts will get
wet and electric shock might be resulted.
• If the appliance is not kept in a good state of cleanliness,
this can adversely affect the life of the appliance and result
in a dangerous situation.
• Food residues should be regularly cleaned and removed
from the appliance. If the appliance is not cleaned proper-
ly, it will reduce its lifespan and may result in a dangerous
condition during use.
• DANGER OF INJURY! Care should be taken when handling
the sharp cutting blades during cleaning.
Cleaning
• Clean the cooled exterior surface with a cloth or sponge
slightly dampened with a mild soap solution.
• For reasons of hygiene, the appliance should be cleaned
before and after use.
• Avoid water contacting the electrical components.
• Clean the inside of container with a non-abrasive detergent
and rinse with clean water.
• Never immerse the appliance in water or other liquids.
• Never use aggressive cleaning agents, abrasive sponges, or
cleaning agents containing chlorine. Do not use steel wool,
metallic utensils, or any sharp or pointed objects for clean-
ing. Do not use petrol or solvents!
• No parts are dishwasher safe.
Description
For mixing liquids
For mixing liquids and
solid ingredients
For ice crushing or short,
power impulse movements.
Note: Use the pulse func-
tion for 1 ~ 2 seconds each
time. Repeated about sev-
eral times if necessary.
). If necessary, then
11
GB