Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Maintenance Instruc琀椀ons
We recommend this gas grill be thoroughly inspected and serviced annually by a quali昀椀ed service person.
At all 琀椀mes keep the gas grill area free from combus琀椀ble materials, gasoline and other 昀氀ammable vapors
and liquids. Do not obstruct the 昀氀ow of ven琀椀la琀椀on and combus琀椀on air. Keep the cylinder enclosure
ven琀椀la琀椀on openings (located on the cart sides and at the front and back of the bo琀琀om shelf) free and
clear from debris.
WARNING!
WARNING!
!
possibility of burns, maintenance should be done only when the grill is cool. A leak test must be
performed annually and whenever any component of the gas train is replaced or gas smell is present.
Burner: The burner is made from heavy wall 304 stainless steel, but extreme heat and a corrosive
environment can cause surface corrosion to occur. This can be removed with a brass wire brush.
CAUTION!
Spiders and insects are a琀琀racted to the smell of propane and natural gas. The burner is equipped with an
insect screen on the air shu琀琀er, which reduces the likelihood of insects building nests inside the burner
but does not en琀椀rely eliminate the problem. A nest or web can cause the burner to burn with a so昀琀 yellow
or orange 昀氀ame or cause a 昀椀re (昀氀ashback) at the air shu琀琀er underneath the control panel. To clean the
inside of the burner, it must be removed from the gas grill: Remove the screw (s) that a琀琀aches the burner
to the back wall. Slide the burner back and up wards to remove. Cleaning: Use a 昀氀exible venturi tube
brush to clean the inside of the burner. Shake any loose debris from the burner through the gas inlet.
Check the burner ports and valve ori昀椀ces for blockages. Burner ports can close over 琀椀me due to cooking
debris and corrosion, use an opened paperclip or the supplied port maintenance bit to clean them. Drill
out blocked ports using this drill bit in a small cordless drill. The ports are easier to clean if the burner is
removed from the grill, but it can also be done with the burner installed. Do not 昀氀ex the drill bit when
drilling the ports, as this will cause the drill bit to break. This drill is for burner ports only, not for the brass
ori昀椀ces (jets) which regulate the 昀氀ow into the burner. Take care not to enlarge the holes. Ensure the insect
screen is clean, 琀椀ght, and free of any lint or other debris.
Reinstalla琀椀on: Reverse the procedure to reinstall the burner. Check that the valve enters the burner when
installing. Replace sear plate mount and / or 琀椀ghten screws to complete reinstalla琀椀on.
WARNING!
!
important that the valve/ori昀椀ce enters the burner tube before ligh琀椀ng your
gas grill. If the valve is not inside the burner tube a 昀椀re or explosion could
occur.
WARNING!
!
hose. If any of these condi琀椀ons exist, do not use the gas grill. Have the part replaced by your Napoleon
Gas Grill dealer or quali昀椀ed gas installer.
Aluminum Cas琀椀ngs: Clean cas琀椀ngs periodically with warm soapy water. Aluminum will not rust, but high
temperatures and weathering can cause oxida琀椀on to occur on aluminum surfaces. This appears as white
spots on the cas琀椀ngs. To re昀椀nish these areas, clean 昀椀rst and sand lightly with 昀椀ne sandpaper. Wipe the
surface to remove any residue and paint with high temperature barbecue paint. Protect surrounding
areas from over-spray. Follow the manufacture's direc琀椀ons for curing.
N415-0542CE-GB-DE FEB 01.22
Always wear protec琀椀ve gloves and safety glasses when cleaning your grill.
Turn o昀昀 the gas at the source and disconnect the unit before servicing. To avoid the
Beware of Spiders.
When reinstalling the burner a昀琀er cleaning it is very
Regulator Hose (when applicable): Check for abrasions', mel琀椀ng, cuts, and cracks in the
13
EN
www.napoleon.com
Werbung
