Herunterladen Inhalt Inhalt Diese Seite drucken

General Power Tool Safety Warnings; Work Area Safety; Electrical Safety; Personal Safety - Ryobi RCS1835 Bedienungsanleitung

Vorschau ausblenden Andere Handbücher für RCS1835:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 23
GB
F
D
E
I
OPERATING INSTRUCTIONS
Dear Customer:
Thank you for buying a Ryobi power tool. Each Ryobi
power Tool is carefully tested and subjected to strict
quality controls by TTI quality assurance. Nevertheless,
the service life of a power tool depends to a great extent
on you. Please observe the information contained in
these instructions and enclosed documentation. The more
carefully you treat your Ryobi power tool, the longer it will
provide dependable service.

GENERAL POWER TOOL SAFETY WARNINGS

WARNING
Reading the operating instructions will reduce the
Risk of injury.
WARNING
Reading all safety Warnings and instructions
Failure to follow the warnings and instructions May
result in electric shock, fire and or Serious injury.
Save all warnings and instructions for future
reference.

WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c) Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose
control.

ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs And matching outlets will reduce
risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
P
NL
S
DK
N
FIN GR HU
English
CZ RU
RO PL SLO HR TR EST LT
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
f) If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
NOTE: The term "residual current device (RCD)" may
be replaced by the term "ground fault circuit interrupter
(GFCI)" or "earth leakage circuit breaker (ELCB)".

PERSONAL SAFETY

a) Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol medication.
A moment of inattention while operating power tools
may result in serious personal injury.
b) Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust
mask, nonskid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries. Ryobi advise the use of chainsaw
clothing complying to class 1 (use for chainsaws).
c) Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the
switch or energising power tools that have the switch
on invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
e) Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
POWER TOOL USE AND CARE
a) Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
11
LV
SK BG

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Rcs2040

Inhaltsverzeichnis