Intended Use; Power Supply - Makita HR2653 Betriebsanleitung

ENGLISH (Original instructions)
SPECIFICATIONS
Model:
Capacities
No load speed
Blows per minute
Overall length
Net weight
Safety class
• Due to our continuing program of research and development, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• The weight may differ depending on the attachment(s). The lightest and heaviest combination, according to
EPTA-Procedure 01/2014, are shown in the table.

Intended use

The tool is intended for hammer drilling and drilling in
brick, concrete and stone.
It is also suitable for drilling without impact in wood,
metal, ceramic and plastic.

Power supply

The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated and can, therefore, also be used
from sockets without earth wire.
Noise
The typical A-weighted noise level determined accord-
ing to EN60745-2-6:
Model HR2652
Sound pressure level (L
Sound power level (L ) : 102 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Model HR2653
Sound pressure level (L
Sound power level (L ) : 103 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Model HR2653T
Sound pressure level (L
Sound power level (L ) : 103 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Model HR2663
Sound pressure level (L
Sound power level (L ) : 101 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Concrete
Core bit
Diamond core bit (dry type)
Steel
Wood
) : 91 dB(A)
pA
) : 92 dB(A)
pA
) : 92 dB(A)
pA
) : 90 dB(A)
pA
HR2652 HR2653
0 - 1,200 min
0 - 4,600 min
604 mm
3.0 - 4.3 kg 3.1 - 4.3 kg
NOTE: The declared noise emission value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared noise emission value(s) may
also be used in a preliminary assessment of exposure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared
value(s) depending on the ways in which the tool is
used especially what kind of workpiece is processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
Vibration
The following table shows the vibration total value
(tri-axial vector sum) determined according to applica-
ble standard.
Model HR2652
Work mode Vibration
emission
Hammer 12.5 m/s
drilling into
concrete
(a )
h, HD
Chiselling func- 9.5 m/s
tion with side
grip (a )
h, Cheq
Drilling into 2.5 m/s
metal (a )
h, D
8 ENGLISH
HR2653T
26 mm
68 mm
80 mm
13 mm
32 mm
-1
0 - 1,100 min
-1
0 - 4,500 min
630 mm
3.2 - 4.5 kg 3.3 - 4.6 kg
/II
Uncertainty (K) Applicable
standard
2 2
1.5 m/s EN60745-2-6
2 2
1.5 m/s EN60745-2-6
2 2
1.5 m/s EN60745-2-1
HR2663
-1
-1
666 mm