Intended Use - Makita HR008G Betriebsanleitung

Intended use

The tool is intended for hammer drilling and drilling in
brick, concrete and stone as well as for chiselling work.
It is also suitable for drilling without impact in wood,
metal, ceramic and plastic.
Noise
The typical A-weighted noise level determined accord-
ing to EN62841-2-6:
Model HR008G
Sound pressure level (L
Sound power level (L ) : 103 dB (A)
WA
Uncertainty (K) : 3 dB (A)
Model HR009G
Sound pressure level (L
Sound power level (L ) : 103 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Model HR008G with DX10
Sound pressure level (L
Sound power level (L ) : 105 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Model HR009G with DX11
Sound pressure level (L
Sound power level (L ) : 105 dB (A)
WA
Uncertainty (K) : 3 dB(A)
NOTE: The declared noise emission value(s) has
been measured in accordance with a standard test
method and may be used for comparing one tool with
another.
NOTE: The declared noise emission value(s)
may also be used in a preliminary assessment of
exposure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared
value(s) depending on the ways in which the
tool is used especially what kind of workpiece is
processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
) : 92 dB (A)
pA
) : 92 dB(A)
pA
) : 94 dB(A)
pA
) : 94 dB(A)
pA
Vibration
The following table shows the vibration total value
(tri-axial vector sum) determined according to applica-
ble standard.
Model HR008G
Work mode Vibration
emission
Hammer 11.8 m/s
drilling into
9.1 m/s
concrete
(a )
h, HD
Hammer 9.5 m/s
drilling into
7.8 m/s
concrete with
DX10 (a )
h, HD
Chiselling 8.6 m/s
(a )
h, CHeq
8.0 m/s
Model HR009G
Work mode Vibration
emission
Hammer 11.5 m/s
drilling into
9.1 m/s
concrete
(a )
h, HD
Hammer 8.9 m/s
drilling into
7.3 m/s
concrete with
DX11 (a )
h, HD
Chiselling 7.3 m/s
(a )
h, CHeq
7.1 m/s
* The test condition of recommended practical operation
meets EN 62841-2-6, except for the following points:
• Feed force is applied to the switch handle (main
handle) for working accuracy and efficiency.
• The side grip/handle (auxiliary handle) is held to
keep balance of the tool.
NOTE: The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
WARNING:
use of the power tool can differ from the declared val-
ue(s) depending on the ways in which the tool is used
especially what kind of workpiece is processed.
WARNING:
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
13 ENGLISH
Uncertainty (K) Applicable
2 2
1.5 m/s
2 2
1.5 m/s
2 2
2.0 m/s
2 2
1.5 m/s
2 2
1.5 m/s
2 2
1.5 m/s
Uncertainty (K) Applicable
2 2
1.5 m/s
2 2
1.5 m/s
2 2
1.5 m/s
2 2
1.5 m/s
2 2
1.5 m/s
2 2
1.5 m/s
The vibration emission during actual
Be sure to identify safety mea-
standard /
Test condition
EN62841-2-6
Recommended
practical
operation*
EN62841-2-6
Recommended
practical
operation*
EN62841-2-6
Recommended
practical
operation*
standard /
Test condition
EN62841-2-6
Recommended
practical
operation*
EN62841-2-6
Recommended
practical
operation*
EN62841-2-6
Recommended
practical
operation*