Fitting The Battery; Charging The Battery - EINHELL VENTURRO 36/240 Originalbetriebsanleitung

5.5 Fitting / removing the catch bag
•
Slip the catch bag connection (Fig. 2 / Item
10a) over the mount (Fig. 8a / Item 10b) on
the motor housing. Make sure that it latches
in place correctly (Fig. 8b).
•
Hook the catch bag on the suction tube in
one of the two holes (Fig. 8c / Item 8a/8b)
(Fig. 8d). The hole (Fig. 8c / Item 8c) cannot
be used on this model.
To remove the catch bag, unhook it from the suc-
tion tube. Press the release levers (Fig. 8b / Item
10c) simultaneously on the left and right and pull
off the catch bag.

5.6 Fitting the battery

Press the pushlock button (Item C) of the rechar-
geable battery as shown in Fig. 9a and push the
battery into the battery mount provided until it
latches in place. Fig. 9b shows the rechargeable
batteries when fi tted. To remove the battery pack,
proceed in reverse order.
Notice!
Never combine batteries with diff erent capacities
(Ah).
Use only batteries which are charged to the same
level. Never combine full and half-full batteries.
Always charge the two batteries simultaneously.
The equipment's operating time depends on the
battery with the lower charge level. The two batte-
ries must always be fully charged before use.

5.7 Charging the battery

1. Take the battery pack out of the equipment.
To do so, press the pushlock button (Fig. 9a/
Item C).
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
into the socket outlet. The green LED will then
begin to fl ash.
3. Insert the battery pack into the charger (Fig.
10).
4. In the section entitled „Charger indicator" you
will fi nd a table with an explanation of the LED
indicator on the charger.
The rechargeable battery can become a little
warm during the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
Anl_Venturro_36_240_SPK13.indb 22 Anl_Venturro_36_240_SPK13.indb 22
GB
If the battery pack still fails to charge, send
•
the charger
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
Battery capacity indicator (Fig. 11)
Press the button for the battery capacity indicator
(Item A). The battery capacity indicator (Item B)
shows the charge status of the battery using 3
LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
- 22 -
05.04.2022 15:14:27 05.04.2022 15:14:27