Before Using The Equipment; Suction Tube - EINHELL VENTURRO 36/240 Originalbetriebsanleitung

Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
•
Wear ear-muffs.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
4. Risk of eye damage if suitable safety goggles
are not worn.
This equipment generates an electromagnetic
fi eld during operation. Under certain circumstan-
ces this fi eld may actively or passively impede
medical implants. To reduce the risk of serious
or fatal injuries, we recommend persons with
medical implants to consult their doctor and the
manufacturer of the medical implant prior to using
the equipment.
Anl_Venturro_36_240_SPK13.indb 21 Anl_Venturro_36_240_SPK13.indb 21
GB

5. Before using the equipment

The equipment is supplied without batteries
and without a charger.
Warning!
Always remove the batteries before making
adjustments to the equipment.
5.1 Preparations

5.1.1 Suction tube

Connect the top suction tube (Fig. 3a/Item 6) and
the bottom suction tube (Fig. 3a/Item 8) together.
Make sure that the guide lug (Fig. 3a/Item A) is in-
serted into the corresponding recess (Fig. 3a/Item
B) when you do this. Make sure that it latches in
place correctly as well.
Screw the two tubes together in addition with the
tapping screw (Fig. 3b/Item 7). Now slide the fully
assembled suction tube into the motor housing
(Fig. 4a) and secure it with the two star screws
(Fig. 4b/Item 4).
Important!
Please note that the two suction tubes must al-
ways be joined together before they are mounted
on the motor housing, and that they must then
never be taken apart again.
Integrated safety switches will be pressed and the
machine supplied with voltage only after the fully
assembled suction tube has been properly scre-
wed to the motor housing.
5.2 Fitting the castors
Press the two levers (Fig. 5a / Item 9a) and push
the castors (Fig. 5a/5b / Item 9) onto the front
suction tube (Fig. 5a / Item 8). Three fi xed locking
positions (Fig. 5a / Item 8a) are possible for set-
ting the working position as preferred.
5.3 Fitting the wall bracket
Push the wall bracket (Fig. 6a / Item 11) onto the
motor housing (Fig. 6b) as far as the stop. Make
sure that the V-shaped cut-out (Fig. 6b / Item 11a)
faces the suction tube in order to be able to hang
the machine from a screw in the wall. The wall
bracket also serves as a support when the machi-
ne is placed on the ground.
5.4 Fitting the harness
Pull back the catch (Fig. 7 / Item 5a) of the carabi-
ner and hook it on the motor housing (Fig. 7).
- 21 -
05.04.2022 15:14:27 05.04.2022 15:14:27