Fuel And Oil; Switching Off The Engine; Practical Tips - EINHELL 34.038.35 Originalbetriebsanleitung

5.2 Fuel and oil

Recommended fuels
Use only a mixture of normal unleaded petrol and
special 2-stroke engine oil. Mix the fuel mixture as
indicated on the fuel mixing table.
Please note: Do not use a fuel mixture which has
been kept for longer than 90 days.
Please note: Do not use 2-stroke oil with a
recommended mixing ration of 100:1. If inade-
quate lubrication causes engine damage, the
manufacturer's engine warranty will be voided.
Please note: Only use containers designed and
approved for the purpose to transport and store
fuel.
Pour the correct quantities of petrol and 2-stroke
oil into the mixing bottle (see scale printed on the
bottle). Then shake the bottle well.
5.3 Fuel mixture table
Mixing procedure: 40 parts petrol to 1 part oil
Petrol
1 liters
5 liters
6. Operation
Please note that the statutory regulations gover-
ning noise abatement may diff er from one loca-
tion to another.
Operate and start the equipment only outdoors
in well ventilated areas to reduce the danger of
injury from toxic gases.
6.1 Starting the engine from cold (Fig. 3-5)
Fill the tank with the required amount of oil/petrol
mix.
1. Set the equipment down on a hard, level sur-
face.
2. Set the choke lever (Fig. 4/Item 5) to
3. Press the fuel pump (primer) (Fig. 4/Item 9)
10 times.
4. Move the On/Off switch (Fig. 3/Item 6) to "I".
5. Hold the machine by the front handle in your
left hand and pull the starter cable (Fig. 5/Item
A) up to the fi rst resistance point (approx. 10
cm) with your right hand. Then tug sharply
on the starter cable 4 times. The equipment
Anl_GE_PH_2555_A_SPK7.indb 19 Anl_GE_PH_2555_A_SPK7.indb 19
GB
2-stroke oil
25 ml
125 ml
.
- 19 -
should start.
Important: Never allow the starter line to snap
back. This may result in damage.
6. Once the engine has started, allow the equip-
ment to warm up for 10 seconds.
Important: Since the choke lever is secured,
the cutting tool will start to operate when the
engine is started.
Actuate the choke lever once to release the
throttle (Item 14). (The engine will then return
to idle mode.) Remember: Before you can
actuate the throttle lever, you must press the
throttle lever "Release" lever through as far as
the stop.
7. If the engine does not start up, repeat steps
5-6.
Please note: If the engine does not start up even
after several attempts, read the section "Engine
troubleshooting".
Please note: Always pull the starter cable out in
a straight line. If it is pulled out at an angle, friction
will occur on the eyelet. As a result of this friction,
the cable will become frayed and will wear away
faster.
6.2 Starting the engine when warm (if the ma-
chine has not been switched off for more
than 15-20 minutes)
1. Put the equipment down on a hard, level sur-
face.
2. Move the On/Off switch to "I".
3. Hold the machine by the front handle in your
left hand and pull the starter cable up to the
fi rst resistance point (approx. 10 cm) with
your right hand. Then tug sharply on the star-
ter cable. The equipment should start after
1-2 tugs. If the equipment does not start after
6 pulls, repeat steps 1-7 of the procedure for
starting the engine from cold.
6.3 Switching off the engine
Emergency Stop procedure:
If it becomes necessary to stop the machine im-
mediately, set the ON/OFF switch to "Stop" or "0"
Normal procedure:
Let go of the throttle lever and wait until the engi-
ne has changed to idling speed. Then set the ON/
OFF switch to "Stop" or "0".

6.4 Practical tips

Never allow the machine to run at low speed for
starting or for cutting.
08.04.2019 08:37:00 08.04.2019 08:37:00