Before Starting The Equipment; Fuel And Oil - EINHELL BG-PT 2542 Bedienungsanleitung

Anleitung_BG_PT_2542_SPK1:_
GB
Cutting line diameter:
Tank capacity
Spark plug
Vibration a rear handle
hv
L sound pressure level
pA
L sound power level
WA
Sound and vibration were measured in accordance
with DIN EN 22868.

5. Before starting the equipment

5.1 Assembly
5.1.1 Assembly of the long handle (Fig. D - E)
Remove the transport guard cap from the lower long
handle. Slacken the star grip screw (Fig. D/Item A)
on the connecting piece on the upper long handle
(Fig. D/Item B). Carefully slide the lower long handle
(Fig. D/Item C) into the connecting piece on the
upper long handle.
When doing so, take care to ensure that the drive
shafts on the insides of the long handles slide into
each other (turn the spool head gently, if required)
and that the lock on the lower long handle (Fig.
E/Item D) latches securely in the connecting piece.
Now retighten the star grip screw (Fig. D/Item A). To
dismantle, proceed in reverse order.
5.1.2 Fitting the guard hood (Fig. F1 – F2)
Attach the guard hood to the lower long handle (Fig.
F1). Screw the guard hood tightly in position with the
fastening set (Fig. F2).
5.1.3 Fitting the carrying strap (Fig. G)
The carrying strap is intended to help you work safely
and ergonomically with the power trimmer. Hook the
carrying strap into the fastening eyelet (Fig. G/ Item
A).
Check that all moving parts move smoothly before
you start using the machine. Check that all screws
are securely fastened and also check all the safety
devices.
5.1.4 Fitting the additional handle (Fig. G1 – G3)
Slacken the wing nut on the fastening screw on the
handle (Fig. G1/Item 1). Remove the nut and the
fastening screw (Fig. G1/Item 3) from the handle and
insert them in the long handle (Fig. G2). Then screw
the handle to the long handle (Fig. G3).
20
Downloaded from www.Manualslib.com
12.01.2009 14:08 Uhr
2.0 mm
0.45 l
Torch L8RTC
7.45 m/s 2
101 dB (A)
110 dB (A)
manuals search engine
Seite 20
5.2 Setting the cutting height
Slip the shoulder strap (Fig. B/17) over the left
shoulder.
Set the length of the shoulder strap in such a way
that the cutting head runs parallel to the ground.
In order to establish the optimum length of the
shoulder strap, you should then make a few
swinging movements without starting the engine
(Fig. I).
Please note: Always use the shoulder strap when
using the appliance. Attach the strap as soon as you
have started the engine and the engine is running in
idle mode. Switch off the engine before you take off
the shoulder strap.
Check the machine for the following each time before
use:
That there are no leaks in the fuel system
That the cutting unit and all safety devices are in
perfect condition
That all screws are securely fastened

5.3 Fuel and oil

Recommended fuels
Use only a mixture of normal unleaded petrol and
special 2-stroke engine oil. Mix the fuel mixture as
indicated on the fuel mixing table.
Please note: Do not use a fuel mixture which has
been kept for longer than 90 days.
Please note: Do not use 2-stroke oil with a
recommended mixing ration of 100:1. If inadequate
lubrication causes engine damage, the
manufacturer's engine warranty will be voided.
Please note: Only use containers designed and
approved for the purpose to transport and store fuel.
Pour the correct quantities of petrol and 2-stroke oil
into the mixing bottle (see scale printed on the bottle).
Then shake the bottle well.
5.4 Fuel mixture table
Mixing procedure: 25 parts petrol to 1 part oil
Petrol 2-stroke oil
1 liters 40 ml
2 liters 200 ml