Changing The Blades; Cleaning, Maintenance And Ordering Of Spare Parts; Ordering Replacement Parts; Disposal And Recycling - EINHELL GE-CG 12 Li Originalbetriebsanleitung

6.3 Changing the blades

Warning! Risk of injury!
To remove the blade, press the release mecha-
nism (Fig. 1/Item 12) and take out the blade as
shown in Fig. 12/Item 12.
Once you have removed the blade you will be
able to see the toothed wheels of the gear unit
(Fig. 13). Make sure that no dirt gets into the gear
unit when you change the blade.
To assemble, proceed in the reverse order.
Caution! The blade will fall out when the release
mechanism is pressed (Fig. 1/Item 12)!
When you fi t the hedge cutter blade
check the position of the pin for the eccentric
connector (Fig. 13/Item 1). Take the hedge cutter
blade and slide the eccentric mount (Fig. 14/Item
1) into position so that the pin for the eccentric
connector and the eccentric mount fi t together
precisely when assembled. Slot the hedge cutter
blade onto the guide pins (Fig. 13/Item 2).
When you fi t the grass cutter blade
check the position of the pin for the eccentric con-
nector (Fig. 13/Item 1) again. Shift the eccentric
mount (Fig. 15/Item 1) on the grass cutter blade
to the left or the right to fi nd the position at which
the pin for the eccentric connector (Fig. 13/Item
1) and the eccentric mount (Fig. 15/Item 1) match
up.
7. Cleaning, maintenance and
ordering of spare parts
Danger!
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth. Do not use cleaning agents or solvents;
these could attack the plastic parts of the
equipment. Ensure that no water can seep
into the device. The ingress of water into an
electric tool increases the risk of an electric
shock.
•
A few drops of oil (e.g. sewing machine oil)
Anl_GE-CG_12_Li_SPK9.indb 20 Anl_GE-CG_12_Li_SPK9.indb 20
GB
will improve the cutting performance of the
blades, but never apply any grease to the
blades.
•
To ensure constant exact cutting it is also
important to remove grass remnants and dirt
from between the upper and lower blade.
Caution!
Never clean the tool under running water
- and particularly never with high pressure -
because of the potential danger to persons
and property. Keep your cordless grass
cutter and hedge trimmer in a dry and frost-
proof place. Choose a place that children are
unable to enter.
7.2 Maintenance
•
To achieve good results you should keep the
blades sharp at all times. In particular we re-
commend that you immediately level off any
jags or ridges caused by stones or the like.
The tool should be thoroughly cleaned both
before and after use.
•
There are no parts inside the equipment
which require additional maintenance.

7.3 Ordering replacement parts:

Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info

8. Disposal and recycling

The unit is supplied in packaging to prevent its
being damaged in transit. This packaging is raw
material and can therefore be reused or can be
returned to the raw material system.
The unit and its accessories are made of various
types of material, such as metal and plastic. De-
fective components must be disposed of as spe-
cial waste. Ask your dealer or your local council.
- 20 -
25.04.2017 08:59:23 25.04.2017 08:59:23