Setting The Cutting Height; Operation - EINHELL 34.010.48 Bedienungsanleitung

Anleitung_BG_PM_46_SE_SPK1:_
GB

5.2 Setting the cutting height

Important! Adjust the cutting height only when
the engine is switched off and the plug boot has
been pulled.
Before you begin to mow, check to ensure that
the blade is not blunt and that none of the
fasteners are damaged. To prevent any
imbalance, replace blunt and/or damaged blades
as a set only (if applicable). To carry out this
check, first switch off the engine and pull the
spark plug boot.
The cutting height is centrally adjusted with the
cutting height adjustor lever
(Fig. 1/Item 9). Up to 5 different cutting heights
can be selected.
Pull the adjustor lever out and select the desired
cutting height. The lever snaps into the desired
position.

6. Operation

Important!
The engine does not come with oil in it.
Therefore, ensure that you add 0.6 liters of oil
before starting it up. Use normal, multigrade oil
(15W40). The oil level in the engine must be
checked each time before mowing. (see
Checking the oil level).
In order to avoid any unintentional start-ups of the
lawn mower, it comes equipped with an engine
brake (Fig. 10/Item A) which must be pulled back
before the engine can be started. When the engine
control lever is released it must return to its initial
position, at which point the engine automatically
switches off.
Before you start the lawn mower, open the petrol
cock (Fig. 11, arrow = petrol cock open). Move the
speed lever (Fig. 12) to position "N". Press the
engine brake lever (Fig. 10/Pos. A) together and
give the starter cord a vigorous pull. You can
control the rotation speed of the blade using the
speed lever (Fig. 12).
Before you start mowing, you should run through
this operation several times in order to ensure that
the machine is working properly.
Whenever you need to perform any kind of adjust-
ment and/or repair work on your lawn mower, wait
until the blade has come to a complete stop.
24
24.03.2009 8:57 Uhr Seite 24
Always switch off the engine before carrying out any
adjustments, maintenance or repairs.
Note:
1. Engine brake (Fig. 10/Item A): Use the lever to
stop the engine. When you release the lever the
engine and the blade stop automatically (Fig.
10/Pos. A). To mow, hold the lever in the working
position. Before you start to mow, check the
start/stop lever several times to be sure that it is
working properly. Ensure that the tension cable
can be smoothly operated (i.e. is not catching or
kinking in any way).
2. Speed lever (Fig. 12): Move this lever in order to
increase or decrease the engine speed. (Tortoise
= Slow / Hare = Fast)
3. Drive lever (clutch lever) (Fig. 1/Item 1): If you
press this (Fig. 13/Item B) the clutch for the drive
will be closed and the lawnmower will start to
move with the motor running.
Release the drive lever in good time to stop the
moving lawnmower. Practice starting and
stopping before you use the mower for the first
time until you are familiar with controlling the
mower.
4. Caution: The blade begins to rotate as soon as
the engine is started.
Important:
Before you start the engine, move the motor
brake several times to be sure that the stop
cable is properly working. Note: The engine is
factory set to a speed that is optimal for cutting
and blowing grass into the basket and is
designed to provide many years of use.
5. Check the oil level.
6. Fill the tank with approx. 1.1 liters of petrol
whenever empty, using a funnel and measuring
jug to do so. Ensure that the petrol is free of any
contaminants.
Note: Use only unleaded petrol as fuel.
Warning: Never use more than one safety petrol
can. Do not smoke when refueling. Switch off the
engine before refueling and allow the engine to cool
down for a few minutes.
6. Ensure that the ignition cable is connected to the
spark plug.
7. Move the speed lever to position "N".
8. Stand behind the mower. Place one hand on the
engine start/stop lever. Place the other hand on
the starter handle.
9. Start the engine using the reversing starter (Fig.
1/Item 5). To do this pull the handle approx. 10 –
15 cm (until you feel a resistance) and then start
the engine with a sharp pull. If the engine does
not start, pull the handle again.