Before Starting The Equipment; Assembling The Components; Setting The Cutting Height - EINHELL BG-PM 51 S HW Originalbetriebsanleitung

Anleitung_BG_PM_51_S_HW_SPK7:_
GB

6. Before starting the equipment

6.1 Assembling the components

Some parts of the mower come disassembled. For
quick and easy assembly, read and follow the
instructions below.
Important. You will need the following additional
tools (not supplied) for assembly, and also for
maintenance work:
A flat oil drip tray (for changing the oil)
A 1 liter measuring jug (oil/petrol resistant)
A petrol can
A funnel (suitable for the tank's petrol filler neck)
Household wipes (to wipe up oil/petrol residue;
dispose of these at a filling station)
A petrol suction pump (plastic, available from DIY
stores)
An oil can with hand pump (available from DIY
stores)
Engine oil
Assembly
1. Fasten the push bar (Fig. 3a/Item 3) using one
screw (Fig. 3a/Item 12) and one star nut (Fig.
3a/Item 11) on each side. For fastening choose
one of the holes to suit the required height of the
push bar. Important. The identical height must be
set on both sides. Ensure that the cords which
are fastened later are not in the way.
2. Fasten the top push handle to the bottom push
handle with the star screws (Item 11) as shown in
Fig. 3b.
3. Insert the grip of the starter cord (Fig. 3c/Item 9)
into the hook provided for that purpose as shown
in Figure 3c.
4. Fasten the cords to the push bar with the
supplied cable clips (Fig. 3d/Item 10).
5. Lift the ejector flap (Fig. 4a / Item 5a) with one
hand and hook in the grass bag (Fig. 4a/Item 4a)
as shown in Figure 4a.

6.2 Setting the cutting height

Important. Adjust the cutting height only when
the engine is switched off and the plug boot has
been pulled.
Before you begin to mow, check to ensure that
the blade is not blunt and that none of the
fasteners are damaged. To prevent any
imbalance, replace blunt and/or damaged blades
as a set only (if applicable). To carry out this
check, first switch off the engine and pull the
spark plug boot.
The cutting height is centrally adjusted with the
cutting height adjustor lever
26
29.07.2010 11:29 Uhr Seite 26
(Fig. 7/Item 8). Different cutting heights can be
selected.
Pull the setting lever into the desired position.
Allow the lever to engage.
7. Using the petrol lawn mower
Important.
The engine is supplied without oil and petrol.
Therefore, be sure to add oil and petrol before
starting the engine.
In order to avoid any unintentional start-ups of the
lawn mower, it comes equipped with an engine brake
(Fig. 5a/Item 1a) which must be pulled back before
the engine can be started. When the engine start/stop
lever is released it must return to its initial position, at
which point the engine automatically switches off.
Move the throttle control (Fig. 6) in position
the motor start/stop lever (Fig. 5b) and vigorously pull
the starter cable (pull start). Set the desired working
speed.
You should repeat this procedure several times
before starting to cut the grass to make sure that
everything is working correctly. Be sure to wait until
the blade has stopped rotating before performing any
adjusting and/or repair works to your lawn mower.
Switch off the engine before performing any
adjusting, maintenance or repair works.
Note:
1. Engine brake (Fig. 5a/Item 1a): Use the engine
start/stop lever to switch off the engine. When
you release the engine start/stop lever, the
engine and blade will automatically stop. To mow,
hold the lever in the working position (Fig. 5b).
Before you start to mow, check the start/stop
lever several times to be sure that it is working
properly. Ensure that the tension cable can be
smoothly operated (i.e. is not catching or kinking
in any way).
2. Drive lever/clutch lever (Fig. 5a/Item 1b): If you
press this (Fig. 5c) the clutch for the drive will be
closed and the lawnmower will start to move with
the engine running. Release the drive lever in
good time to stop the moving lawnmower.
Practice starting and stopping before you use the
mower for the first time until you are familiar with
controlling the mower.
3. Warning: The blade begins to rotate as soon as
the engine is started.
Important: Before you start the engine, move the
engine brake several times to be sure that the
stop cable is properly working.
. Pull