Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
More safety warnings - „Service"
Repairs to other parts of the machine must be carried
out by the manufacturer or one of his customer ser-
vice points.
Use only original spare parts. Accidents can arise for
the user through the use of other spare parts. The
manufacturer is not liable for any damage or injury
resulting from such action.
D
e
s
c
r
i
p
t
i
o
n
o
f
D
e
s
c
r
i
p
t
i
o
n
o
f
,
Pos.
Denomination
1.
Agitator
2.
Spiral beater
3.
ON / OFF-switch
4.
Locking knob
5.
Speed control
6.
2-speed switch
7.
Handle
8.
Shaft
9.
Spanners
10.
Mortar beater
11.
Disk beater
12.
Agitator stand
13.
Carbon brush cover
14.
Carbon brushes (2pcs)
A
s
A
Chucking the beater:
Screw the beater assembly (2) on the shaft (8). Secure
the beater using the spanners (9).
S
S
Do not use any device where the switch can not be
switched on and off. Damaged switches must be repaired
or replaced immediately by the customer service.
Check that the machine is completely and correctly assem-
bled.
Before each use, check
Connection cables for defects (cracks, cuts, etc.).
Do not use any defective cables.
there are no damages at the machine
(see "safe working")
that the beater is properly secured.
d
e
v
i
c
e
/
S
p
a
r
e
p
a
r
t
s
d
e
v
i
c
e
/
S
p
a
r
e
p
a
r
t
s
Order-No.
RW 1400-2
RW 1800-2
372613
372616
372562
372612
372615
372614
372614
372653
372627
372639
372629
372641
s
e
m
b
l
y
s
s
e
m
b
l
y
t
a
r
t
-
u
p
t
a
r
t
-
u
p
Mains connection
Compare the voltage given on the machine model plate e.g.
230 V with the mains voltage and connect the machine to
the relevant and properly earthed plug.
Connect the machine via a 30 mA fault current safety
switch.
Do not use any defective connection cables.
Use connecting or extension cables up to a length of 1.5 m
featuring a core cross section of at least 25 mm²
Main fuse: 10 A
Switching on/off
Do not use any device where the switch can not be swit-
ched on and off. Damaged switches must be repaired or
replaced immediately by the customer service.
Switching on
Press the ON/OFF button (3) on the handle. The de-
vice will slowly start after powering up.
Switching off
Release the ON/OFF handle button.
2- speed gear
The device is equipped with a 2-speed gear.
1.
speed: 150 - 300 rpm
2.
speed: 300 - 650 rpm
For the speed selection turn the switch (6) by 180°.
Only operate this switch at standstill.
Continuous operation
Switching on
For continuous operation press the locking knob (4) in
switched on condition.
Use the agitator only in continuous mode with the
agitator stand fitted.
Optional accessories: Agitator stand, order-no.:
372652
The device cuts off automatically in case of power fail-
ure. Press the switch again to restart the machine.
Switching off
Press the ON/OFF button (3).
Speed control
With this type, the motor's speed and thus the agitator perfor-
mance can be adjusted.
You can continuously adjust the speed with the speed
control (4).
1. speed: 150 - 300 rpm
2. speed: 300 - 650 rpm
14
Werbung
Inhaltsverzeichnis
