Seite 1
All manuals and user guides at all-guides.com 1434 Pos Intelligenter Stellungsregler für fremdgesteuerte Linearantriebe Intelligent positioner for pneumatically operated linear actuators ORIGINAL EINBAU- UND MONTAGEANLEITUNG INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS Stand 07.10.16 Ab Version 1.1.2.1 Status 07th October 2016 From version 1.1.2.1 1434 µPos...
All manuals and user guides at all-guides.com Inhaltsverzeichnis Hinweise zu Ihrer Sicherheit Bitte lesen Sie die nachfolgenden Hinweise Hinweise zu Ihrer Sicherheit sorgfältig durch und beachten Sie diese. Allgemeines Hinweise zur Sicherheit Allgemeines Bestimmungsgemäßer Gebrauch Eine einwandfreie Funktion unseres GEMÜ Hinweise für den Einsatz in 1434 Pos setzt folgendes voraus: feuchter Umgebung...
All manuals and user guides at all-guides.com nationalen Vorschriften. Bestimmungsgemäßer Die Beschreibungen und Instruktionen in Gebrauch dieser Sicherheitsanweisung beziehen sich Der GEMÜ 1434 Pos ist für den Einsatz auf die Standardausführung. entsprechend dem Datenblatt in bestimmten Die Sicherheitshinweise berücksichtigen ortsfesten Anlagen geeignet. nicht Zufälligkeiten und Ereignisse, Um eine einwandfreie Funktion unserer die bei Montage, Betrieb und Wartung...
All manuals and user guides at all-guides.com Hinweise für den Einsatz in Installation mit geführter Abluft. Die Abluft muss jedoch nur am Anschluss 3 abgeführt feuchter Umgebung werden. Eine Reinigung des GEMÜ 1434 1. Pneumatische Hilfsenergie deaktivieren. Pos darf unter keinen Umständen 2.
All manuals and user guides at all-guides.com 6. Pneumatikverschraubung in Wartung und Service Gewindeadapter einschrauben und Der GEMÜ 1434 Pos unterliegt bei einem vorsichtig festziehen. Einbau und Einsatz gemäß dieser Einbau- und Montageanleitung und des Datenblattes keiner Wartung / Service. Helfen Sie mit das Produkt weiter zu entwickeln und leiten Sie abweichendes Verhalten gegenüber der Beschreibung...
All manuals and user guides at all-guides.com Mechanischer Anbau Komplettierung des Weggebers VORSICHT Vorgespannte Feder! ® Beschädigung des Gerätes. Spindel festhalten und Betätigungs- spindel handfest anziehen. Feder langsam entspannen. VORSICHT Eine Beschädigung der Spindeloberfl äche kann zum Ausfall des Weggebers führen! Der Weggeber wird mit einem Anbausatz 1434S01Z...
All manuals and user guides at all-guides.com Anbau des Stellungsreglers Bei GEMÜ 650 beiliegend (O-Ring C nur bei Steuerfunktion 2 und 3): Druckscheibe B O-Ring C Ventil mit Stellungsregler Weggeber komplettieren (siehe Kapitel 3.1 „Komplettierung des Weggebers“). Stellungsregler 1 auf Antrieb 3 bzw. Adapter E aufsetzen und mit einem geeigneten Gabelschlüssel SW 20 / SW 24 am Weggeber 2 fi...
All manuals and user guides at all-guides.com Anbau des externen Anbau des Stellungsreglers Weggebers (nur bei Variante mit Befestigungswinkel mit externem Anbau) Der Anbau des Stellungsreglers mit Befestigungswinkel wird bei Ventilen angewandt, die eine größere Stel- lungsänderung verrichten als der integrierte Weggeber des Stellungs- reglers erfassen kann.
All manuals and user guides at all-guides.com Pneumatische Anschlüsse Bei Ausführung mit externem Weggeber: X3 wird nur in Kombination mit externem Wegmessystem benötigt. Anschluss Pin Signalname UP+, Ausgang Potentiometer Versorgungsspannung (+) UP, Eingang Anschluss- Potentiometerschleiferspannung Bezeichnung schluss größe A-kodiert UP-, Ausgang Potentiometer M12 - Dose Versorgungsluftanschluss P Versorgungsspannung (-)
All manuals and user guides at all-guides.com Elektrischer und 2. Initialisierungsspannung deaktivieren. pneumatischer Anschluss Symbol Symbol OPEN CLOSED 1. Pneumatische Hilfsenergie ERROR POWER (max. 8/10 bar) aktivieren. Legende +24V DC Symbol Blinkt schnell Blinkt langsam 2. Versorgungsspannung 24 V einschalten. 3.
All manuals and user guides at all-guides.com Anzeigeelemente OPEN ERROR CLOSED POWER Bezeichnung Farbe OPEN gelb ERROR CLOSED orange POWER gelb LED 1 LED 2 LED 3 LED 4 Bedeutung Fehlernummer OPEN ERROR CLOSED POWER Position erreicht Ventil in Endlage AUF Ventil in Endlage ZU Ventil fährt in Richtung AUF Ventil fährt in Richtung ZU...
All manuals and user guides at all-guides.com Fehlermeldungen Fehler Fehlermeldung Fehlerursache Auswirkung Fehlerbehebung Sollwert > 20,5 mA / Sollwertsignal > 20,5 mA / Prozessventil Nr. 1 Sollwertsignal überprüfen 10,25 V 10,25 V wird entlüftet Prozessventil Nr. 2 Sollwert < 3,5 mA Sollwertsignal <...
All manuals and user guides at all-guides.com Maße Externer Anbau [mm] Direkter Anbau [mm] 13,6 SW24 M20x1,5 SW24 13,6 SW27 SW 20 bei Anbausatz M12 x1, x = 9 mm SW 24 bei Anbausatz M16 x1, x = 11 mm Befestigungswinkel [mm] 1434 µPos 13 / 32...
All manuals and user guides at all-guides.com Technische Daten Elektrische Daten Allgemeines Schutzart nach EN 60529 IP 65 / IP 67 ¹⁾ Spannungsversorgung Gewicht 220 g Spannungsversorgung = 18...30 V DC Maße L x B x H siehe Bemaßung ≤ 4 W (bis 24 V DC) Leistungsaufnahme Einbaulage beliebig...
All manuals and user guides at all-guides.com Bestelldaten Feldbus Code Anschluss Pneumatisch Code Ohne (3-Leiter Ausführung) Zuluft / Ausgang über M5 Anschlussgewinde Zuluft / Ausgang über Schnellsteckverbinder winklig, 4 mm Zubehör Code Zuluft / Ausgang über Schnellsteckverbinder winklig, 6 mm Zubehör Option Code...
All manuals and user guides at all-guides.com EU-Konformitätserklärung EU-Konformitätserklärung Wir, die Firma GEMÜ Gebr. Müller Apparatebau GmbH & Co. KG Fritz-Müller-Straße 6-8 D-74653 Ingelfingen erklären, dass das unten aufgeführte Produkt der folgenden Richtlinie entspricht: • EMV-Richtlinie 2014/30/EU Produkt: GEMÜ 1434 Joachim Brien Leiter Bereich Technik Ingelfingen-Criesbach, September 2016...
All manuals and user guides at all-guides.com Contents Notes for your safety Please read the following notes carefully and Notes for your safety observe them! General information Safety notes General information Correct use Important requirements to ensure that our Information on use in damp GEMÜ...
All manuals and user guides at all-guides.com operating instructions refer to the standard Correct use version. The GEMÜ 1434 Pos is suitable for use The safety information does not take into in specific fixed plant as defined in the data account unexpected incidents and events sheet.
All manuals and user guides at all-guides.com Information on use in damp 1. Deactivate the pneumatic control air supply. conditions 2. Remove the protective caps from Under no circumstances connection 3 and E using a small whatsoever may the GEMÜ 1434 screwdriver.
All manuals and user guides at all-guides.com 6. Screw the pneumatic connection into the Service and maintenance threaded adapter and carefully tighten it. When installed and used in accordance with these installation, operating and maintenance instructions and the data sheet, the GEMÜ 1434 Pos is not subject to any service and maintenance.
All manuals and user guides at all-guides.com Mechanical mounting Assembling the travel sensor CAUTION Pretensioned spring ® Damage to the device. Slowly release the tension in the spring. Hold the spindle and tighten the operating bush hand tight. CAUTION Damage to the spindle surface may lead to failure of the travel sensor! The travel sensor is assembled using a 1434S01Z...
All manuals and user guides at all-guides.com Mounting the positioner Enclosed for GEMÜ 650 (O-ring C only for control functions 2 and 3): Pressure disc B O-ring C Valve with positioner Assemble the travel sensor (see chapter 3.1 “Assembling the travel sensor”). Place the positioner 1 on actuator 3 or adapter E and fi...
All manuals and user guides at all-guides.com Mounting the external travel Mounting the positioner using sensor (only for version with a mounting bracket remote mounting) The positioner is mounted with a mounting bracket when valves are used which have larger position changes than the integrated travel sensor on the positioner can detect.
All manuals and user guides at all-guides.com Pneumatic connections In the version with external travel sensor: X3 is only required in combination with an external travel sensor system. Connection Pin Signal name UP+, output potentiometer supply voltage (+) Connec- Connection UP, input potentiometer wiper Designation tion...
All manuals and user guides at all-guides.com Electrical and pneumatic 2. Deactivate initialisation power supply. connection Symbol Symbol OPEN CLOSED 1. Activate pneumatic control air supply ERROR POWER (max. 8/10 bar). +24V DC Symbol Flashes fast Flashes slowly 2. Switch on 24 V power supply. 3.
All manuals and user guides at all-guides.com Display elements OPEN ERROR CLOSED POWER Designation Colour OPEN Yellow ERROR CLOSED Orange POWER Yellow LED 1 LED 2 LED 3 LED 4 Meaning Error number OPEN ERROR CLOSED POWER Position reached Valve in OPEN end position Valve in CLOSED end position Valve moves in OPEN direction Valve moves in CLOSED direction...
All manuals and user guides at all-guides.com Error messages Error Error message Error cause Effect Error clearance Set value > 20.5 mA / Set value signal Process valve No. 1 Check set value signal 10.25 V > 20.5 mA / 10.25 V is vented Process valve No.
All manuals and user guides at all-guides.com Dimensions Remote mounting [mm] Direct mounting [mm] 13,6 SW24 M20x1,5 SW24 13,6 SW27 SW 20 for mounting kit M12 x1, x = 9 mm SW 24 for mounting kit M16 x1, x = 11 mm Mounting bracket [mm] 1434 µPos 28 / 32...
All manuals and user guides at all-guides.com Technical data General information Electrical data Protection class to EN 60529 IP 65 / IP 67 ¹⁾ Power supply Weight 220 g Power supply = 18...30 V DC Dimensions L x W x H See dimensional drawing ≤...
All manuals and user guides at all-guides.com Order data Field bus Code Pneumatic connection Code Air supply / output Without (3-wire version) via M5 connection thread Air supply / output via push-in connector,angle, 4 mm Accessory Code Air supply / output Accessory via push-in connector, angle, 6 mm Option...
All manuals and user guides at all-guides.com EU Declaration of Conformity EU Declaration of Conformity Hereby we, GEMÜ Gebr. Müller Apparatebau GmbH & Co. KG Fritz-Müller-Straße 6-8 D-74653 Ingelfingen declare that the product listed below complies with the following directive: •...
Seite 32
All manuals and user guides at all-guides.com GEMÜ Gebr. Müller Apparatebau GmbH & Co. KG · Fritz-Müller-Str. 6-8 · D-74653 Ingelfi ngen-Criesbach Telefon +49(0)7940/123-0 · Telefax +49(0)7940/123-192 · info@gemue.de · www.gemu-group.com...