Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
NOTICE:
Do not attempt to cut branches thicker
than 10 mm in diameter with the tool. Cut branches
to 10 cm lower than the cutting height using branch
cutters before using the tool.
► Fig.22: (1) Cutting height (2) 10 cm
NOTICE:
Do not cut down dead trees or similar
hard objects. Doing so may damage the tool.
Hold the tool with both hands by holding the front han-
dle of the power unit or the front grip of the attachment
and the rear grip of the power unit.
► Fig.23: 1. Front handle 2. Rear grip
Pull the switch trigger while pressing the lock-off lever,
and then move the tool forward.
► Fig.24
For basic operation, tilt the shear blades toward the
trimming direction and move it calmly and slowly at the
speed rate of 3 to 4 seconds per meter.
► Fig.25
To cut a hedge side evenly, cut from the bottom to top.
► Fig.26
When trimming to make a round shape (trimming box-
wood or rhododendron, etc.), trim from the root to the
top for a beautiful finish.
► Fig.27
When shearing the grass, apply the shear blades to the
grass parallel to the ground, and shear the grass with a
right to left swinging movement.
► Fig.28
MAINTENANCE
WARNING:
Before inspecting or maintaining
the equipment, switch off the motor and remove
the battery cartridge. Otherwise, the machine may
start unintentionally and result in serious injury.
WARNING:
When inspecting or maintaining
the equipment, always put it down. Assembling or
adjusting the equipment in an upright position may
result in serious injury.
WARNING:
Follow the warnings and precau-
tions in the chapter "SAFETY WARNINGS" and
the instruction manual of the power unit.
CAUTION:
Wear gloves when performing the
inspection or maintenance.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
Cleaning the tool
Clean the tool by wiping off dust with a dry cloth or one
dipped in soapy water and wrung out.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
Shear blade maintenance
Before the operation or once per hour during operation,
apply low-viscosity oil (machine oil, or spray-type lubri-
cating oil) to the shear blades.
► Fig.29
After operation, remove dust from both sides of the shear blades
with a wired brush, wipe it off with a cloth and then apply low-viscos-
ity oil (machine oil, or spray-type lubricating oil) to the shear blades.
► Fig.30
NOTICE:
Do not wash the shear blades in water.
Doing so may cause rust or damage to the tool.
NOTICE:
Dirt and corrosion cause excessive blade
friction and shorten the operating time per battery charge.
Storage
Attach the blade cover to the shear blades so that the blades
are not exposed. Store the tool out of the reach of children.
Store the tool in a place not exposed to moisture or rain.
When storing the attachment separated from the power
unit, put the cap onto the end of the pipe.
► Fig.31
Lubricating moving parts
NOTICE:
Follow the instruction of the frequency
and amount of grease supplied. Otherwise insuffi-
cient lubrication may damage moving parts.
Drive axle:
Apply grease (Makita grease N No.2 or equivalent)
every 30 hours of operation.
► Fig.32
NOTE: Genuine Makita grease may be purchased
from your local Makita dealer.
Grease lubrication
Interval of lubrication: Every 25 operating hours
1.
Remove the bolt from the hole for lubrication.
► Fig.33: 1. Bolt
2.
Remove the cap from the grease vessel. Align the
outlet of the grease vessel with the hole on the cover,
and then turn the grease vessel to attach the outlet of
the grease vessel into the hole.
► Fig.34: 1. Grease vessel 2. Hole
3.
Apply the grease to the tool (Approximately 3 g as a guide).
4.
Remove the grease vessel.
5.
Tighten the bolt.
13 ENGLISH
Werbung
Inhaltsverzeichnis
