Specific Safety Rules; Functional Description - Makita 6845 Betriebsanleitung

ENGLISH
1 Lock button
2 Switch trigger
3 Reversing switch lever
4 Hook
5 Clamping screw
6 Casing
7 Thumb screw
8 Plane bearing
9 Dust cover
SPECIFICATIONS
Model
Screw strip ................................ 4 mm x 25 mm – 41 mm
-1
No load speed (min ) ............................................. 4,700
Overall length ..................................................... 333 mm
Net weight .............................................................. 1.9 kg
Safety class .............................................................
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for screw driving in wood, metal and
plastic.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product
(gained from repeated
adherence to screwdriver safety rules. If you use
this power tool unsafely or incorrectly, you can
suffer serious personal injury.
1. Hold power tool by insulated gripping surfaces,
when performing an operation where the fas-
tener may contact hidden wiring or its own cord.
Fasteners contacting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
2. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
3. Hold the tool firmly.
4. Keep hands away from rotating parts.
5. Do not touch the bit or the workpiece immedi-
ately after operation; they may be extremely hot
and could burn your skin.
SAVE THESE INSTRUCTIONS.
Explanation of general view
10 Bit
11 Lever
12 Stopper base
13 Plate
14 Adjusting knob
15 Lock lever
16 Magazine cap
17 Screw strip
18 Magazine
6845
/II
GEB017-2
use) replace strict
19 Slotted passage
20 Portion A
21 Screw-driving position
22 Reverse button
23 Extension handle
24 Limit mark
25 Brush holder cap
26 Screwdriver
WARNING:
MISUSE or failure to follow the safety rules stated
in this instruction manual may cause serious
personal injury.

FUNCTIONAL DESCRIPTION

CAUTION:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.
Switch action (Fig. 1)
CAUTION:
• Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
"OFF" position when released.
To start the tool, simply pull the switch trigger. Release
the switch trigger to stop.
Reversing switch action (Fig. 2)
This tool has a reversing switch to change the direction of
rotation. Depress the reversing switch lever from the A
side for clockwise rotation or from the B side for counter-
clockwise rotation.
CAUTION:
• Always check the direction of rotation before operation.
• Use the reversing switch only after the tool comes to a
complete stop. Changing the direction of rotation
before the tool stops may damage the tool.
Hook (Fig. 3)
The hook is convenient for hooking the tool to your belt. It
can be installed on either side of the tool.
Changing the installation position of hook allows two-way
setting of 10 mm and 20 mm distance from the tool itself.
The tool with hook can be hung on the waist belt, a maxi-
mum diameter 20 mm pipe etc.
To remove the hook, just remove the clamping screw.
Place it on the tool and secure it with the clamping screw
to install.
5