Specification; Specific Safety Rules - Makita BTS130 Betriebsanleitung

ENGLISH
1 Button
2 Red part
3 Battery cartridge
4 Switch trigger
5 Lamp
6 Reversing switch lever
7 Bit
8 Sleeve
9 Bit-piece

SPECIFICATION

Model
Machine screw
Capacities Standard bolt
High tensile bolt
No load speed (min
Impacts per minute
Overall length
Net weight
Rated voltage
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for screw driving in wood, metal and
plastic.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product
(gained from repeated
adherence to impact driver safety rules. If you
use this tool unsafely or incorrectly, you can
suffer serious personal injury.
1. Wear ear protectors with impact drivers. Expo-
sure to noise can cause hearing loss.
2. Hold power tools by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed metal
parts of the tool "live" and shock the operator.
3. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
4. Hold the tool firmly.
SAVE THESE INSTRUCTIONS.
4
Explanation of general view
10 Hook
11 Screw
12 Groove
13 Air vents
14 Cooling down oil unit
15 Standard bolt
16 Fastening torque
17 Proper fastening torque
18 Fastening time
BTS130
M4 – M8
M6 – M10
M6 – M8
–1
) 0 – 2,400
0 – 1,600
183 mm
1.7 kg
D.C. 14.4 V
GEB012-1
use) replace
WARNING:
MISUSE or failure to follow the safety rules stated
in this instruction manual may cause serious
personal injury.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER & BATTERY CARTRIDGE
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using bat-
tery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any conduc-
tive material.
(2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins,
etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
strict
6. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
7. Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.
8. Be careful not to drop or strike battery.
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1. Charge the battery cartridge before completely
discharged.
Always stop tool operation and charge the bat-
tery cartridge when you notice less tool power.
2. Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
3. Charge the battery cartridge with room tempera-
ture at 10°C – 40°C (50°F – 104°F). Let a hot bat-
tery cartridge cool down before charging it.
19 High tensile bolt
20 Limit mark
21 Rear cover
22 Screws
23 Spring
24 Arm
25 Recessed part
26 Carbon brush cap
27 Hole
ENC007-1