Specifications; Specific Safety Rules - Makita 6319D Betriebsanleitung

ENGLISH
(Original instructions)
1 Button
2 Battery cartridge
3 Switch trigger
4 Reversing switch lever
5 Speed change lever
6 Action mode change lever
7 Arrow
8 Adjusting ring

SPECIFICATIONS

Model
Capacities
Steel ..................................................... 13 mm
Wood .................................................... 45 mm
Wood screw.......................................... 6 mm x 75 mm
Machine screw ..................................... 6 mm
-1
No load speed (min )
High (3)................................................. 0 – 1,600
Medium (2) ........................................... 0 – 550
Low (1) ................................................. 0 – 300
Overall length .......................................... 246 mm
Net weight ............................................... 2.3 kg
Rated voltage .......................................... D. C. 12 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications and battery cartridge may differ from
country to country.
• Weight, with battery cartridge, according to EPTA-Pro-
cedure 01/2003
Intended use
The tool is intended for drilling and screw driving in wood,
metal and plastic.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to drill safety rules. If you use this power tool
unsafely or incorrectly, you can suffer serious per-
sonal injury.
1. Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
2. Hold power tools by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
3. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
4
Explanation of general view
9 Graduations
10 Steel band
11 Grip base
12 Side grip
13 Protrusion
14 Groove
15 Sleeve
16 Bit
6319D
4.
5.
6.
7.
8.
GEA010-1
SAVE THESE INSTRUCTIONS.
WARNING:
MISUSE or failure to follow the safety rules stated in
this instruction manual may cause serious personal
injury.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER & BATTERY CARTRIDGE
GEB001-4
1.
2.
3.
4.
5.
6.
17 Bit holder
18 Depth rod
19 Clamp screw
20 Limit mark
21 Brush holder cap
22 Screwdriver
6339D
13 mm
50 mm
6 mm x 75 mm
6 mm
0 – 1,700
0 – 600
0 – 300
246 mm
2.4 kg
D. C. 14.4 V
Hold the tool firmly.
Keep hands away from rotating parts.
Do not leave the tool running. Operate the tool
only when hand-held.
Do not touch the drill bit or the workpiece imme-
diately after operation; they may be extremely
hot and could burn your skin.
Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation and
skin contact. Follow material supplier safety data.
Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using battery.
Do not disassemble battery cartridge.
If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
Always cover the battery terminals with the bat-
tery cover when the battery cartridge is not used.
Do not short the battery cartridge:
(1) Do not touch the terminals with any conduc-
tive material.
6349D
13 mm
65 mm
10 mm x 89 mm
6 mm
0 – 1,700
0 – 600
0 – 300
246 mm
2.6 kg
D. C. 18 V
ENC004-1