Operation - Jamestown Xander Bedienungsanleitung

GB
– Check all seals for damages. Do not install addi-
tional seals.
– Screw the coupling nut (2) of the pressure regula-
tor (3) by hand in an anti-clockwise direction onto
the tank connection thread (left thread).
Checking the seals
– Brush soap solution onto the coupling nut (2) and
connection thread (4) of the hose (5) and examine
for bubble formation.
The connections are sealed correctly if no bubbles form.
DANGER! Explosion hazard! Carrying out a
check of the seals using naked flames is
strictly forbidden!
Comply with all safety instructions when han-
dling gas!
When checking for leaks, ensure that there are
no sources of ignition in the vicinity. Do not
smoke!
Porous or damaged hoses and fittings must be
replaced.

Operation

DANGER! Risk of burning! Wear BBQ
gloves and appropriate clothing.
DANGER! Risk of cuts Every care has been
taken at the factory to ensure that there are no
sharp edges on this unit. Be careful when han-
dling the individual components of this unit to
prevent accidents and injuries when assem-
bling and starting up the unit.
Check before use!
Check to make sure the device is in a safe operating
condition:
– Check to make sure there are no visible defects.
– Check to make sure all device components are cor-
rectly mounted.
– Check all gas connections for leaks.
– Check that all regulators are set to OFF.
– Open the grill hood fully.
Lighting
DANGER! Risk of burning injury due to
potential grease fire! A grease fire may
result in serious property damage and per-
sonal injuries.
Before use, check the removable grease trap
and collection tray for grease.
Remove excess grease to prevent grease
fires.
DANGER! Risk of burning! Always open the
hood fully before igniting.
Do not lean over the grilling area!
Before igniting
– Open the hood of the BBQ grill fully.
– Clean the grilling surface thoroughly.
– Fully open the tank valve.
Main burner lighting instructions
1. Push the control knob in, hold it down for 3-5 sec-
onds and then turn it anticlockwise to „HIGH".
2. Keep pushing down the control knob for 2 seconds
at „HIGH" position before releasing it.
34
3. If ignition does not occur within 3 seconds, turn con-
trol knob to „OFF", and repeat ignition step 1 and 2.
Infrared side burner lighting instructions
1. Push the infrared side burner control knob down and
turn it anticlockwise to „HIGH"and press the elec-
tronic ignition button until burner ignites. Continue to
hold down the infrared side burner control knob for
5 seconds at "HIGH" position after the burner has
ignited and then release the infrared side burner
control knob.
2. If ignition does not occur in 5 seconds, turn the
burner control knob to „OFF", wait 5 minutes, and
repeat step 1
Use of infrared-gasburners (side burners):
– Do not close the cover during use. First let the infra-
red-gasburner cool down for 5 minutes.
Manual igniting
– Fully open the tank valve.
– Press the relevant rotating regulator and set to
"large flame" and, at the same time, feed a lit match
that is as long as possible through the hole in the
side of the grill basin.
– To ignite the other burner, press the rotating regula-
tor and set to "large flame". The flame will transfer of
its own accord.
Setting the flame height
• Turn the regulator anti-clockwise = small flame
• Turn the regulator clockwise = large flame
Flames that are too large and flicker, as well as flames
with yellow tips signalise that the burner nozzles are
contaminated.
– Turn the regulator clockwise as far as it will go to
switch off the relevant burner.
– Fully close the tank valve.
Grilling
– Operate the grill for 30 minutes on the highest level
(without food) before you use it to remove any pro-
duction residue.
DANGER! Risk of burning! When the grill
hood is close, never use more than two burn-
ers on the highest setting at the same time.