Unpacking; Assembly - Scheppach 5907732930 Originalbetriebsanleitung

Wear hearing protection.
Excessive noise can result in a loss of hearing.
Total vibration emission values (vector sum of three
directions) determined per EN 60335.
Vibration emission value a
The specified vibration emission value has been meas-
ured according to a standardised testing procedure
and can be used for comparison of one power tool with
another; and may change depending on the way in
which the power tool is used and in exceptional cases
may be higher than the specified value.
The specified vibration emission value can be used to
compare one power tool with another.
The specified vibration emission value can also be
used for an initial estimation of the impair.
Keep the noise level and vibration to a minimum!
• Only use faultless devices.
• Maintain and clean the device at regular intervals.
• Adapt your working methods to the device.
• Do not overload the device.
• Have the device checked if necessary.
• Switch the device off if it is not in use.
• Wear gloves.
7.

Unpacking

• Open the packaging and carefully remove the de-
vice.
• Remove the packaging material, as well as the pack-
aging and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the device and accessory parts for transport
damage. In the event of complaints the carrier must
be informed immediately. Later claims will not be
recognised.
• If possible, keep the packaging until the expiry of the
warranty period.
• Familiarise yourself with the device by means of the
operating manual before using for the first time.
• With accessories as well as wearing parts and re-
placement parts use only original parts. Spare parts
can be obtained from your specialist dealer.
• When ordering please provide our article number as
well as type and year of manufacture for your equip-
ment.
24 | GB
≤ 2,5 m/s
2
h
www.scheppach.com
m WARNING!
The device and the packaging material are not
children's toys! Do not let children play with plas-
tic bags, films or small parts! There is a danger of
choking or suffocating!

8. Assembly

8.1 Assembling the device (Fig. 3)
1. Push the handle (1) onto the fastening point at
the top of the device and use the included screws
(7) to secure it.
2. Slide the lance holder (2) and the cable holder
(5) onto the side of the connection point on the
device.
8.2 Water supply connection (Fig. 4)
1. Screw the adapter for the water supply (10) onto
the water supply connection (4).
2. The adapter for the water supply (10) features a
connection for standard hose coupling systems.
Attach the hose coupling of the supply hose (min.
Ø 1/2"/ approx. 13 mm) onto the connection for the
water supply (10).
3. Always use an enhanced water hose with an in-
dustry-standard coupling (not included in the
scope of delivery) for the water supply. The length
should be at least 6.0 m.
4. A backflow prevention device must be installed
between the drinking water and the high-pressure
cleaner! Ask your plumbing expert about this.
8.3 High-pressure hose connection (Fig. 5, 6)
1. Connect the high-pressure hose (9) to the con-
nection for the high-pressure hose (6). Remove
the protective cover first.
2. Insert the other end of the high-pressure hose (9)
into the pistol connection (13).
3. To remove the high-pressure hose (9), press the
button Taste (A) and pull it out.
8.4 Connecting the attachments (Fig. 6)
1. Screw the extension (12) into the retainer for the
pistol (13).
2. To use the detergent container (8), insert it into the
extension (12) and turn it until it locks into place.
3. To use the nozzle (14), first mount the spray lance
(11). Insert spraying lance (11) in the extension
(12) and turn until it locks. Now connect the nozzle
(14) on the spray lance (11). Make sure that the
nozzle (14) is locked.