Elica Aria nuova Montage- Und Gebrauchsanweisungen Seite 12

● Delay off
Using the Radio Control, it is possible to program the
delayed switch-off according to the suction speed (power)
active at that time; the speeds at which this function can be
enabled are the following:
Speed 1 (low extraction): 20 min.
Speed 2 (medium extraction): 15 min.
Speed 3 (high extraction): 10 min.
Note (only for products with Wi-Fi function): The Delay
off function can be programmed in a more advanced way,
when connected to the Elica Cloud, via the Elica Connect
App. However, in this case, it will not be possible to
manage the Delay off function from the Radio Control, until
the Wi-Fi is reset or switched off.
● Activating/Deactivating the filter saturation indicator
light
To be performed with the product switched off. The
carbon filter saturation indicator light is usually deactivated,
while the grease filter saturation indicator light is usually
activated.
With Radio Control 1:
Odour Filter: Simultaneously press keys A+B+D for 2 sec.
each press switches sequentially from active to inactive.
(Active = LED L1 steady Red and LED L2 flashing Red.
Inactive = LED L1 steady Red and LED L2 Off)
Grease Filter: Simultaneously press keys A+B+C for 2
sec. each press switches sequentially from active to
inactive. (Active = LED L1 steady Orange and LED L2
flashing Orange. Inactive = LED L1 steady Orange and
LED L2 Off)
Wait 10 sec. to save the chosen setting.
With Radio Control 2:
This procedure is described in the Radio Control manual.
Wait 10 sec. to save the chosen setting.
● Filter saturation indicator lights
The LEDs on the hood indicate the need to perform
maintenance on the filters.
Odour filter: L1 + L2 flashing Red.
Grease filter: L1 + L2 flashing Orange.
Note: The filter saturation indication is visible for 10 sec.
when the hood is switched on. After performing
maintenance on the filters, it is necessary to perform the
filter saturation reset.
● Filter saturation reset
This operation must be performed within the first 10sec.
after switching on the product.
The procedure is described in the Radio Control manual.
Note: If there are two active warnings, for both grease and
odour filters, the operation must be performed twice.
● Automatic suction speed function (VOC function):
This product is equipped with a sensor (VOC sensor) that
modulates the suction speed automatically according to the
amount of smoke detected.
This function must be enabled manually via the Radio
Control or via the Elica Connect App.
When the function is active, LED L1 will light up White.
Once activated, if the sensor detects no smoke for a few
minutes, the motor will be switched off.
Note: The function will still remain active and if within the
next 2 hours the sensor detects some steam, the motor
will be restarted automatically. After 2 continuous hours
without detecting any smoke, the function is disabled. It is
always possible to disable this function manually, at any
time, via the Radio Control or via the Elica Connect App.
● VOC sensor calibration:
Calibration is necessary to allow the product sensor to work
correctly; calibration is performed in two ways:
Automatic: each time the hood is reconnected to the
mains (e.g. the first time it is installed or after a power
failure).
Manual: Manual calibration requires that the product motor
is OFF and that normal environmental conditions persist in
the room where it is installed. This operation must be
performed when automatic operation is unsatisfactory.
With Radio Control 1:
Simultaneously press A+D for 2 sec.
With Radio Control 2:
This procedure is described in the Radio Control manual.
During calibration, LED L1 flashes Green.
To cancel the current calibration, repeat the procedure
used to start the calibration.
● Hob settings (for VOC sensor)
To use the VOC function in the best way possible, it is
necessary to select the correct type of hob from those
available: GAS - Induction or Electric. By Default, the hob
is set to GAS.
This setting requires that the product motor is OFF and that
the VOC sensor is deactivated.
With Radio Control 1:
Simultaneously press keys B+D for 2 sec. an acoustic
signal will indicate that you have entered the hob setting
menu. From here, use the keys B and C to scroll back and
forth to select the desired hob. Each time the key is
pressed, a type of hob will be selected; LED L1 will light up
in a different colour according to the selected hob: Green =
Gas; Yellow = Electric; Cyan = Induction.
With Radio Control 2:
Simultaneously press keys A+D for 2 sec. From here, use
the keys B and C to scroll back and forth to select the
desired hob. Each time the key is pressed, a type of hob
will be selected; LED L1 will light up in a different colour
according to the selected hob: Green = Gas; Yellow =
Electric; Cyan = Induction.
12