Operational Features - Toyotomi TAD-2220E Bedienungsanleitung

SUMMARY
The idea behind the unit is to provide a localized supply of cool air.
The unit will greatly enhance your personal comfort whether at a
work station or even in your favorite chair.
Four (4) casters enable you to move the unit easily from room to
room. It cools and dries the air at the same time so that you can
stay comfortable even when it is humid or rainy outside. Also your
furnishings and fabrics are kept in good condition when it is used
as dehumidifier.
Conventional air conditioners use large quantities of energy to cool
an entire room, including walls and furniture. This unit creates a
zone of cool and dry air only where it is needed. It does not waste
energy cooling the surroundings.
It is easy to operate. The built-in timer allows from 0.5 to 24 hours
of operation, which will automatically turn the unit on and off.
At bedtime, sleep function is convenient. By increasing the preset
temperature by slow degrees, you can sleep more comfortable.
Venting is not required. However, if the unit is to be used exclusive-
ly in one space, the cooling efficiency will be enhanced by using
the venting kit accessory, which is included with the unit.

OPERATIONAL FEATURES

1. COOLING OPERATION / HEATING OPERATION (For TAD-
2235E):
Normally, cool air / heat air (For TAD-2235E) is directed out the
front louvers by the circulation fan.
2. AUTOMATIC OPERATION:
Once the desired function has been set, it is memorized as
long as it remains connected to the wall outlet. In the event of
a power failure, the desired function must be re-entered when
power is restored.
3. THERMO CONTROL:
The compressor will automatically shift to ON or OFF to main-
tain the desired temperature.
4. TIMER OPERATION:
The unit will turn on and off after the designated period of time
(0.5, 1, 1.5, ....24 hours).
5. AUTOMATIC SHUT-OFF MECHANISM WHEN THE DRAIN
TANK IS FULL:
When the chassis is full with water, the unit will be automati-
cally shut off. The buzzer will give out 8 seconds and "H8" is
displayed on the remote controller.
6. AIR FILTER:
A pre-filter protects the unit from dust.
1. DESCRIPTION
Fig. A FRONT
A1 Air outlet
A2 Horizontal louver
A3 Operation panel
A4 Vertical louver
A5 Caster
Fig. B REAR
B1 Air intake (Evaporator)
B2 Exhaust outlet
B3 Air intake (Condenser)
B4 Power supply cord hook
B5 Power plug
B6 Power supply cord
B7 Water drainage outlet for continuous drain operation
(Dehumidify and Cool mode)
B8 Remote control holder
B9 Carrying handle
B10 Air intake grille (Pre-filter)
Fig. C OPERATION PANEL
C1 Power button
C2 Sleep button
C3 Fan speed button
C4 Timer button
C5 Mode button
C6 Adjust buttons
C7 Cool mode lamp
C8 Dehumidify mode lamp
C9 Fan mode lamp
C10 Auto./ High / Med. / Low air flow lamp
C11 X-FAN operation (Internal drying operation) button
C12 Heat mode lamp (For TAD-2235E)
C13 Temperature set button (Not applicable for this unit)
C14 Light button
C15 Health / Save button (Not applicable for this unit)
C16 " ", " " and SWING button (Not applicable for
this unit)
C17 TURBO button (Not applicable for this unit)
C18 CLOCK button
C19
C20 WiFi button
Indication symbols on remote controller
P
O
H
G
F
E
D
I
R
B
8
1 Set fan mode
2 Sending signal
3 (Not applicable for this unit)
4 X-fan operation
(Internal drying operation)
5 Set temperature
6 ON timer / Off timer
7 Set time
8 Light
9 Temperature display type
0 Set temperature
A Indoor ambient temperature
3
button
9
: : : A
: L
B Sleep mode
C Child lock
D Fan mode
E Dehumidify mode
F Cool mode
G Auto. mode
H Operation mode
I Heat mode (For TAD-2235E)
J - P (Not applicable for this unit)
Q WiFi function
R Clock
S Ventilation operation
ENGLISH
1
2
M
S
3
4
5
Q
7
6
C
K