Morso VULCANO WOK BURNER Bedienungsanleitung Seite 16

READ ME FIRST
READ ME FIRST
Gas leak testing
Gas leak testing
It is important that you leak test the BBQ before first use and every time the gas cylinder is refilled and
It is important that you leak test the boiler before first use and every time the gas cylinder is refilled and recon-
reconnected to the BBQ.
nected to the boiler.
To Complete Leak Test
• Make sure all the control knobs are OFF.
To Complete Leak Test
• In a small container, mix up a solution of water and detergent/soap.
• Make sure all the control knobs are OFF.
• Mix the solution well (about the same concentrate as washing up water).
• In a small container, mix up a solution of water and detergent/soap.
• Turn the cylinder ON by rotating the knob to open position.
• Mix the solution well (about the same concentrate as soapy water).
• Using a brush or spay bottle apply the soap solution to the gas line and each join in the gas line including:
• Turn the regulator on the gas bottle to the open position.
- the gas connection at the inlet of the BBQ
• Using a brush or spray bottle apply the soap solution to the gas line and each Connection in the gas line
- all gas hose connections
including:
- the gas connection at the gas cylinder
- the gas connection at the inlet of the boiler
• If bubbles appear, there is a gas leak.
- all gas hose connections
• If the leak is at the connection, re-tighten and re-seal.
- the gas connection at the gas cylinder
• If the leak is anywhere else or you cannot resolve the leak by tightening the connection DO NOT PROCEED.
• If bubbles appear, there is a gas leak.
• Replace gas hose and regulator.
• If the leak is at the connection, re-tighten and re-seal.
• Replace hose and regulators can be purchased from your local BBQ retail specialist.
• If the leak is anywhere else or you cannot resolve the leak by tightening the connection DO NOT PROCEED.
• Replace gas hose and regulator.
• Replacement hose and regulators can be purchased from your local boiler retail specialist. With an original
part from Morsø Jernstøberi A/S.
16
2
READ ME FIRST
READ ME FIRST
Gas leak testing
It is important that you leak test the BBQ before first use and every time the gas
It is important that you leak test the BBQ before first use and every time the gas cylinder is refille
reconnected to the BBQ.
reconnected to the BBQ.
To Complete Leak Test
To Complete Leak Test
• Make sure all the control knobs are OFF.
• Make sure all the control knobs are OFF.
• In a small container, mix up a solution of water and detergent/soap.
• In a small container, mix up a solution of water and detergent/soap.
• Mix the solution well (about the same concentrate as washing up water).
• Mix the solution well (about the same concentrate as washing up water).
• Turn the cylinder ON by rotating the knob to open position.
• Turn the cylinder ON by rotating the knob to open position.
• Using a brush or spay bottle apply the soap solution to the gas line and each joi
• Using a brush or spay bottle apply the soap solution to the gas line and each join in the gas line
- the gas connection at the inlet of the BBQ
- the gas connection at the inlet of the BBQ
- all gas hose connections
- all gas hose connections
- the gas connection at the gas cylinder
- the gas connection at the gas cylinder
• If bubbles appear, there is a gas leak.
• If bubbles appear, there is a gas leak.
• If the leak is at the connection, re-tighten and re-seal.
• If the leak is at the connection, re-tighten and re-seal.
• If the leak is anywhere else or you cannot resolve the leak by tightening the con
• If the leak is anywhere else or you cannot resolve the leak by tightening the connection DO NO
• Replace gas hose and regulator.
• Replace gas hose and regulator.
• Replace hose and regulators can be purchased from your local BBQ retail spec
• Replace hose and regulators can be purchased from your local BBQ retail specialist.
2
2
READ ME FIRST
READ ME FIRST
Gas leak testing Gas leak testing
It is important that you leak test the BBQ before first use and ev
Gas leak testing
reconnected to the BBQ.
It is important that you leak test the BBQ before first use and
reconnected to the BBQ.
To Complete Leak Test
• Make sure all the control knobs are OFF.
To Complete Leak Test
• In a small container, mix up a solution of water and detergent/
• Make sure all the control knobs are OFF.
• Mix the solution well (about the same concentrate as washing
• In a small container, mix up a solution of water and deterge
• Turn the cylinder ON by rotating the knob to open position.
• Mix the solution well (about the same concentrate as wash
• Using a brush or spay bottle apply the soap solution to the gas
• Turn the cylinder ON by rotating the knob to open position
- the gas connection at the inlet of the BBQ
• Using a brush or spay bottle apply the soap solution to the
- all gas hose connections
- the gas connection at the inlet of the BBQ
- the gas connection at the gas cylinder
- all gas hose connections
• If bubbles appear, there is a gas leak.
- the gas connection at the gas cylinder
• If the leak is at the connection, re-tighten and re-seal.
• If bubbles appear, there is a gas leak.
• If the leak is anywhere else or you cannot resolve the leak by t
• If the leak is at the connection, re-tighten and re-seal.
• Replace gas hose and regulator.
• If the leak is anywhere else or you cannot resolve the leak b
• Replace hose and regulators can be purchased from your loca
• Replace gas hose and regulator.
• Replace hose and regulators can be purchased from your lo
2
2