Specifications; Sander Safety Warnings; Functional Description - Makita BO3710 Betriebsanleitung

ENGLISH
1 Lock button
2 Switch trigger
3 Speed adjusting dial
4 Punch plate
5 Abrasive paper without
pre-punched holes

SPECIFICATIONS

Model
Pad size...........................................................93 mm x 185 mm
Abrasive paper size .........................................93 mm x 228 mm
–1
Orbits per minute (min
Overall length ..................................................253 mm
Net weight ......................................................1.6 kg
Safety class .....................................................
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for the sanding of large surface of
wood, plastics and metal materials as well as painted
surfaces.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed Safety
instructions.

SANDER SAFETY WARNINGS

DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. If you use this
tool unsafely or incorrectly, you can suffer serious
personal injury.
1. Always use safety glasses or goggles. Ordinary
eye or sun glasses are NOT safety glasses.
2. Hold the tool firmly.
3. Do not leave the tool running. Operate the tool
only when hand-held.
4. This tool has not been waterproofed, so do not
use water on the workpiece surface.
5. Ventilate your work area adequately when you
perform sanding operations.
6. Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
7. Use of this tool to sand some products, paints
and wood could expose user to dust containing
hazardous substances. Use appropriate respira-
tory protection.
4
Explanation of general view
6 Screwdriver
7 Screw
8 Abrasive paper
9 Pad
10 O-ring
11 Dust spout
BO3710
) ................................11,000
/II
8. Be sure that there are no cracks or breakage on
the pad before use. Cracks or breakage may
cause a personal injury.
SAVE THESE INSTRUCTIONS.
WARNING:
MISUSE or failure to follow the safety rules stated in
this instruction manual may cause serious personal
injury.

FUNCTIONAL DESCRIPTION

CAUTION:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.
Switch action (Fig. 1)
CAUTION:
• Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
"OFF" position when released.
To start the tool, simply pull the switch trigger. Release
GEB021-3
the switch trigger to stop.
For continuous operation, pull the switch trigger and then
push in the lock button.
To stop the tool from the locked position, pull the switch
trigger fully, then release it.
Speed adjusting dial (Fig. 2)
For BO3711 only
CAUTION:
• If the tool is operated continuously at low speeds, the
motor will get overloaded and heated up.
• The speed adjusting dial can be turned only as far as 5
and back to 1. Do not force it past 5 or 1, or the speed
adjusting function may no longer work.
The tool speed can be infinitely adjusted between 4,000
and 11,000 orbits per minute by turning the speed adjust-
ing dial, which is marked 1 to 5. Higher speed is obtained
when the dial is turned in the direction of number 5, lower
speed is obtained when it is turned in the direction of
number 1. Adjust the desired tool speed for the kind of
work.
12 Dust bag
13 Holding tab
14 Dust box
15 Dust nozzle
16 Latch
17 Dust nozzle
BO3711
93 mm x 185 mm
93 mm x 228 mm
4,000 – 11,000
253 mm
1.6 kg
/II