Technical Data; Declaration Of Conformity; Starting Operation - Bosch SmartphoneHub CUI100 Originalbetriebsanleitung

English – 2
(9) Select button
(10) Previous page button
(11) Decrease assistance level button –
(12) Holder for operating unit
(13) Walk assistance button WALK
(14) Increase assistance level/
switch light on or off button +
(15) Operating unit
(16) Universal Mount
(17) Fastening screws for Universal Mount
(18) Front retaining bracket
(19) Rear retaining bracket
a) For mounting on the handlebars, custom solutions are possible
even without the use of the handlebar clamps.
Display elements for SmartphoneHub
a Error indicator
b Bike lights display
c Smartphone connection indicator
d Speed
e Assistance level indicator
f Unit indicator
g Indicator for second battery (optional)
h Battery charge indicator
i State of charge of the battery
j Operating range

Technical data

On-board computer
Product code
Max. USB port charging
current
USB port charging voltage
Operating temperature
Storage temperature
Charging temperature
Internal lithium-ion bat-
tery
Bluetooth® Low Energy
– Frequency
– Transmission power
A)
Protection rating
Weight, approx.
A) When the USB cover is closed
The Bosch eBike system uses FreeRTOS
(see http://www.freertos.org).

Declaration of Conformity

Robert Bosch GmbH, Bosch eBike Systems, hereby declares
that the SmartphoneHub radio communication unit com-
1 270 020 XBC | (11.02.2022)
SmartphoneHub
CUI100
mA 1000
V
°C −5 to +40
°C +10 to +40
°C 0 to +40
V
mAh
MHz 2400–2480
mW
IP 54
kg
plies with Directive 2014/53/EU. The full text of the EU De-
claration of Conformity is available to view at the following
website: https://www.ebike-connect.com/conformity.
Robert Bosch GmbH, Bosch eBike Systems, hereby declares
that the SmartphoneHub radio communication unit com-
plies with the Radio Equipment Regulations 2017 (SI
2917/1206). The full text of the UK Declaration of Conform-
ity can be accessed at the following Internet address:
https://www.ebike-connect.com/conformity.
Operation

Starting Operation

Prerequisites
The eBike system can only be activated when the following
requirements are met:
– A sufficiently charged battery is inserted (see battery op-
erating instructions).
– The speed sensor is connected properly (see drive unit
operating instructions).
Switching the eBike system on/off
The following options are available for switching on the
eBike system:
– Press the on/off button (2) of the on-board computer
with the eBike battery inserted.
– Press the on/off button of the eBike battery (see battery
operating instructions).
The drive is activated as soon as you start pedalling (except
if you are using the walk assistance function or if the assist-
ance level is set to OFF). The motor output adjusts to the as-
sistance level set.
As soon as you stop pedalling when in normal operation, or
as soon as you have reached a speed of 25 km/h, the eBike
drive switches off the assistance. The drive is automatically
reactivated as soon you start pedalling again and the speed
5
is below 25 km/h.
The following options are available for switching off the
eBike system:
– Press the on/off button (2) of the on-board computer.
3.7
– Switch off the eBike battery using its on/off button (bi-
300
cycle manufacturer-specific solutions are possible when
there is no access to the battery on/off button; see the bi-
cycle manufacturer operating instructions).
The system shuts down after being switched off. This takes
< 10
approximately 3 seconds. It cannot be switched back on un-
til shutdown has been completed.
If the eBike is not moved for approx. 10 min and no button is
0.12
pressed on the on-board computer, the eBike system
switches off automatically in order to save energy.
Note: Always switch off the eBike system when you park the
eBike.
Note: If the battery of the SmartphoneHub is empty, you can
still switch on your eBike using the eBike battery. The Smart-
phoneHub battery begins charging automatically once the
Bosch eBike Systems