Assembly - Ferm PSM1023 Gebrauchsanweisung

GB
h. Damaged switches must be replaced at a customer service repair centre. Do not use
power tools that cannot be switched on and off.
D
i. Do not leave power tools unattended while they are switched on. Always switch off the tool
and wait until it has come to a full standstill before leaving.
j. If the mains cable has been damaged, it must be replaced with a special mains cable.
NL
These can be obtained from the manufacturer or the manufacturer's customer service
department. The mains cable may only be replaced by the manufacturer, the
manufacturer's customer service department or equally qualified persons.
F
5. Service
a. Only allow your device to be repaired by qualified technicians and only use original
E
replacement parts. This ensures that the safety of the device is not degraded.
b. Damaged switches must be replaced by our customer service workshop.
c. If the connecting cable (or the power plug) is damaged, it must be replaced by a special
P
connecting cable, which is available from our customer service center. The connecting
cable may only be replaced by our customer service center or by a qualified electrician.
I
6. Special safety regulations for polishing and sanding machines
a. Important! Using accessories or add-on devices other than those recommended in these
operating instructions or included in the delivery kit can pose a hazard that may result in
S
bodily injury.
b. Always use two hands to hold the device when working.
c. Only switch the device on or off when the polishing or sanding disk is on the surface to be
FIN
polished or sanded. Do not leave the device unattended when it is running. Switch off the
device and wait for it to come to a complete stop before putting it down or leaving it
N
unattended.
d. Wear a dust-proof mask when sanding or dry polishing. Connect a vacuum. There is a
suitable adapter in the delivery kit.
DK
e. Avoid using large amounts of polish, otherwise the polishing hood will cannot be easily
removed from the polishing disk. Follow the polish manufacturer's instructions.
f. The sanding and polishing machine is not suitable for wet sanding.
g. If your hair is long, ensure that it is safely tucked away and covered. Do not wear loose-
fitting clothing when operating this device.
h. Always check to ensure that the supply voltage matches the voltage specified on the rating
plate.
i. If necessary, secure the workpiece that you want to sand or polish.
j. Use of extension cables. Only use extension cables that are designed for use with
powered devices. The wire diameter (cross-section) must be at least 1.5 mmÇ. When
using a cable spool, the cable must always be completely unrolled.
k. Before changing accessories, always pull the power plug.
l. Do not sand or polish any materials containing asbestos.

3. ASSEMBLY

See Fig. 2
Pull the power plug before working on the disks!
06
• Vask regelmæssigt polerehætten i hånden i lunkent vand med lidt finvaskemiddel, og lad
den lufttørre.
• Hvis du ikke bruger maskinen i en længere periode, skal du fjerne polerehætten fra
poleretallerkenen. Opbevar maskinen med poleretallerkenen vendende opad.
Fejl
Skulle en fejl opstå, f.eks. pga. slidtage af en enhed, kontakt venligst serviceadressen på
garantibeviset. På bagsiden af denne manual finder du en tegning med alle dele, der kan
bestilles.
Miljø
For at undgå transportbeskadigelse leveres maskinen i en solid emballage. Emballagen er så
vidt muligt lavet af genbrugsmateriale. Genbrug derfor emballagen.
Defekte og/eller kasserede elektriske eller elektroniske maskiner skal afleveres på
en genbrugsplads.
Garanti
Garantibetingelser er beskrevet på det separat vedlagte garantibevis.
CE KONFORMITETSERKLÆRING (DK)
Vi erklærer herved, udelukkende på eget ansvar, at dette produkt, FMMS-120, opfylder
følgende standarder eller standardiserede dokumenter:
EN60745-1, EN50144-1, EN50144-2-3, EN55014-1, EN55014-2, EN61000-3-2,
98/37/EC, 73/23/EEC, 89/336/EEC, 2002/96/EC, 2002/95/EC
03-04-2006
ZWOLLE NL
J.A. Bakker - van Ingen
CEO Ferm BV
Det er vores hensigt til stadighed at forbedre vores produkter, og vi forbeholder os derfor til
enhver tid retten til at ændre produktspecifikationerne uden forudgående varsel.
Ferm BV • Lingenstraat 6 • 8028 PM Zwolle • Holland
Ferm Ferm
EN61000-3-3
i henhold til følgende direktiver:
J. Lodewijk
Quality Manager Ferm Global
UK
D
NL
F
E
P
I
S
FIN
N
DK
79