Before Use - Teac CD-P1120 Bedienungsanleitung

Before Use

Read This Before Operating
O Choose the installation location of your
unit carefully. Avoid placing it in direct
sunlight or close to a source of heat.
Also avoid locations subject to vibra-
tions and excessive dust, heat, cold or
moisture. Keep away from such sources
that hum, such as transformers or
motors.
O Do not open the cabinet as this might
result in damage to the circuitry or elec-
trical shock. If a foreign object should
get into the set, contact your dealer.
O Be sure not to handle discs with dirty
fingers. Never insert a disc which has a
crack on the surface.
O When removing the power plug from the
wall outlet, always pull directly on the
plug, never yank the cord.
O To keep the laser-pickup clean, do not
touch it, and do not forget to close the
disc tray.
O Do not attempt to clean the unit with
chemical solvents as this might damage
the finish. Use a clean, dry cloth.
O Keep this manual in a safe place for
future reference.
Beware of condensation
When the player (or a compact disc) is
moved from a cold to a warm place or
used after a sudden temperature
change, there is the danger of conden-
sation. Water vapor in the air could
condense on the mechanism or the
laser pickup. If droplets of water form
on these parts, correct playback will be
impossible because the laser cannot
read the information from the disc cor-
rectly. To prevent this, if you are going
to use the player in a condition where
condensation could occur, you should
leave the player for 1 or 2 hours after
plugging it into an AC outlet depending
on the amount of condensation. If this
is done, the player will stabilize at the
temperature of its surroundings.
Handling the Discs
This unit has been designed specifically for
reproduction of compact discs bearing the
D
" " mark. No other discs can be repro-
duced.
O Always place the compact disc in the
disc tray with the label facing upward.
(Compact discs can be played only on
one side.)
O To remove a disc from its storage case,
press down on the center of the case
and lift the disc out, holding it carefully
by the edges.
How to remove the disc
How to hold the disc
O Fingermarks and dust should be careful-
ly wiped off the disc's recorded surface
with a soft cloth.
Wipe radially
O Never use such chemicals as record
sprays, antistatic sprays or fluid, ben-
zine or thinner to clean compact discs.
Such chemicals will do irreparable dam-
age to the disc's plastic surface.
O Discs should be returned to their cases
after use to avoid serious scratches that
could cause the laser pickup to "skip."
O Do not expose discs to direct sunlight or
high humidity and temperature for
extended periods.
Long exposure to high temperatures can
warp the disc.
O Do not stick paper or write anything with
a ballpoint pen on the surface of the
label side.
– 4 –
IMPORTANT (for U.K. Customers)
DO NOT cut off the mains plug from this
equipment. If the plug fitted is not suit-
able for the power points in your home
or the cable is too short to reach a
power point, then obtain an appropriate
safety approved extension lead or con-
sult your dealer.
If nonetheless the mains plug is cut off,
remove the fuse and dispose of the plug
immediately, to avoid a possible shock
hazard by inadvertent connection to the
mains supply.
If this product is not provided with a
mains plug, or one has to be fitted, then
follow the instructions given below:
IMPORTANT. DO NOT make any con-
nection to the larger terminal which is
marked with the letter E or by the safety
earth symbol © or coloured GREEN or
GREEN-and-YELLOW.
The wires in the mains lead on this prod-
uct are coloured in accordance with the
following code:
BLUE: NEUTRAL
BROWN: LIVE
As these colours may not correspond
with the coloured markings identifying
the terminals in your plug proceed as
follows:
The wire which is coloured BLUE must
be connected to the terminal which is
marked with the letter N or coloured
BLACK.
The wire which is coloured BROWN
must be connected to the terminal
which is marked with the letter L or
coloured RED.
When replacing the fuse only a correct-
ly rated approved type should be used
and be sure to re-fit the fuse cover.
IF IN DOUBT — CONSULT A COMPE-
TENT ELECTRICIAN.