TempSpray-H326 / -H226 / -H126 Warnung! Beachten Sie die Sicherheitshinweise zu Ihrem Airlessgerät Erdung des Heizschlauches ist immer sicherzustellen. Das Gerät ist nicht explosionsgeschützt ausgeführt -> Achtung beim Einsatz von brennbaren Materialien Vor jeder Inbetriebnahme sind gemäß Betriebsanleitung folgende Punkte zu beachten: 1.
EXPLOSIONS- UND BRANDGEFAHR BEIM ren Speisepunkt mit einer Fehlerstromschutzeinrichtung mit SPRITZEN DURCH ZÜNDQUELLEN INF ≤ 30 mA erfolgen. Im WAGNER Zubehörprogramm finden Es dürfen keine Zündquellen in der Umge- Sie mobile elektrische Personenschutzvor- bung vorhanden sein, wie z.B. offenes Feuer,...
MAX. BETRIEBSDRUCK besteht. Aus Gründen der Funktion, Sicherheit und Der zulässige Betriebsdruck für die Heizschläuche beträgt Lebensdauer nur WAGNER Original-Hoch- 25MPa (250bar). Die Heizschläuche nicht an Farbspritzpum- druckschläuche verwenden. pen mit einem höheren Betriebsdruck verwenden, sofern die- se nicht sicher auf 25MPa begrenzt wurden.
Dispersionen, Heizschläuche. Latexfarben. Ermittelte Richtwerte sind in den Technischen Daten zu jedem Heizschlauch angegeben. Die Verarbeitung anderer Beschichtungsstoffe sollte nur nach Rückfrage bei der Firma WAGNER erfolgen, da die Haltbarkeit und auch die Sicherheit des Gerätes dadurch beeinträchtigt werden können.
TempSpray-H326 / -H226 / -H126 GERÄTEBESCHREIBUNG TRANSPORT TempSpray-H326 und TempSpray-H226: TempSpray-H126: Hochdruckschlauch aufrollen und am Parkstutzen der Hochdruckschlauch aufwickeln (Wickeldurchmesser größer Schlauchführung befestigen. Anschlussschlauch über die Ka- 20 cm). Netzanschlusskabel ebenfalls aufwickeln. belhalter wickeln und ebenfalls am Parkstutzen anschließen. Das Gerät kann mit dem Airlessgerät, an dem es montiert ist Netzanschlusskabel auf Kabelhalter aufwickeln.
TempSpray-H326 / -H226 / -H126 INBETRIEBNAHME INBETRIEBNAHME 4.1.1 TEMPSPRAY-H326 UND TEMPSPRAY-H226 ANSCHLUSS AN DAS STROMNETZ Der Anschluss muss immer über eine vor- 1. Schlauchtrommel in die Nähe des Airlessgerätes stellen. schriftsmäßig geerdete Schutzkontaktsteck- 2. Schlauchpeitsche (1) vom Stutzen am Rahmen lösen und dose mit Fehlerstrom-Absicherung (FI-Siche- Hochdruckschlauch komplett abrollen.
TempSpray-H326 / -H226 / -H126 INBETRIEBNAHME 4.2.1 TEMPSPRAY-H126 ANSCHLUSS AN DAS STROMNETZ Der Anschluss muss immer über eine vor- 1. Reglergehäuse (1) an den Schlauchanschluss des Airless- schriftsmäßig geerdete Schutzkontaktsteck- gerätes montieren, dabei das Gehäuse so ausrichten, das dose mit Fehlerstrom-Absicherung (FI-Siche- es gut zu bedienen ist und keine wichtigen Zugänge am...
TempSpray-H326 / -H226 / -H126 INBETRIEBNAHME EINSCHALTEN TempSpray - H126 Schließen Sie den Heizregler ans Stromnetz an. Im Anzei- gefenster (A) erscheint OFF, um die Betriebsbereitschaft anzuzeigen. Drücken Sie die Taste START (B), um den Heizregler einzuschal- ten. Das Anzeigefenster wechselt von OFF auf die voreinge- stellte Temperatur von 40°C und der Heizvorgang beginnt.
Bei wasserverdünnbaren Beschichtungs- Bei alten Hochdruckschläuchen steigt das stoffen verbessert warmes Wasser die Reini- Risiko von Beschädigungen. gung.Hierzu kann der Heizschlauch einge- Wagner empfiehlt den Hochdruckschlauch schaltet werden. nach 6 Jahren auszutauschen. Aus Gründen der Funktion, Sicherheit und GERÄTEREINIGUNG VON AUSSEN Lebensdauer nur WAGNER Original-Hoch- Zuerst Netzstecker aus der Steckdose ziehen.
Erscheint die Anzeige „0A“ auf dem Display ist der Heiz- leiter in Ordnung. Wird ein anderer Wert für „A“ angezeigt (z.B. 5A), wenden Sie sich bitte an den Wagner Service um eine Isolationsprüfung durchführen zu lassen. 3. Isolation des Heizdrahtes mit Isolationsprüfgerät bei mind.
Platinen Warten Sie ca. 30 Sekunden und schalten Sie es wieder ein. Falls der Fehlercode noch immer angezeigt wird, wenden Sie sich an den Wagner Kunden- dienst. Err2 Steuerplatine erhält keine Rückmeldung Trennen Sie das Gerät vom Netz.
F 07544 - 505-1155 email: kundenzentrum@wagner-group.com Reparatur Hotline T 0180 - 55924637 Mo-Fr. 8.00 - 18.00 Uhr 14 Cent/Minute aus dem deutschen Festnetz, Mobilfunk max. 42 Cent/Min Servicestützpunkte und Fachhändler ganz in Ihrer Nähe fi nden Sie auch im Internet unter go.wagner-group.com/profi...
Tag der Lieferung durch den autorisierten Fachhandel entsprechend den nachfolgenden Bestimmungen registriert. Die Registrierung erfolgt im Internet unter Ihr WAGNER - Altgerät wird von uns, bzw. unseren Handels- www.wagner-group.com/profi-guarantee. vertretungen zurückgenommen und für Sie umweltgerecht Als Bestätigung gilt das Garantiezertifikat, sowie der Original- entsorgt.
Textes dieser Garantie voneinander abweichen, ist die Bedeutung des deutschen Textes vorrangig. Garantieansprüche können nicht berücksichtigt werden für Teile, die einem gebrauchsbedingten oder sonstigen, J. Wagner GmbH natürlichen Verschleiß unterliegen, sowie Mängel am Produkt, Division Professional Finishing die auf einen gebrauchsbedingten oder sonstigen natürlichen Otto Lilienthal Strasse 18 Verschleiß...
Observe the following rules before any work on the unit and at every working break: 1. Relieve the pressure from the spray gun and high-pressure hose. 2. Secure a Wagner spray gun with the securing lever at the trigger guard 3. Switch the unit off.
Seite 30
Spare parts list heating hose DESCRIPTION OF UNIT _____________________ 33 TempSpray-H326 / -H226 ______________________50 General function of the devices ________________ 33 10.5 Spare parts list TempSpray-H126 _______________ 51 Explanatory diagram _________________________ 34 10.6 Spare parts list heating hose Transport __________________________________ 35...
Do not use the unit in work places which are ≤ 30 mA. covered by the explosion protection regula- Wagner‘s accessories program also includes tions. a mobile operator protection device for the The unit is not designed to be explosion pro- electronic supply, which can also be used tected.
The permissible operating pressure for the spray gun, spray it cannot be tripped over. gun accessories, unit accessories and high-pressure hose must Only use WAGNER original-high-pressure not fall short of the maximum operating pressure of hoses in order to ensure functionality, safety 25 MPa (250 bar or 3625 psi).
RANGE OF APPLICATION The heating-hoses TempSpray-H326, TempSpray-H226 and Regard the directions from the colour- TempSpray-H126 are designed for all established Airless paint- manufacturer (technical data sheets of the spraying devices, whose operating pressure is below the rated colours): pressure of the heating-hoses.
Hose drum Frame Lock wheel Governor housing Control panel with display 10 Screw connexion (TempSpray-H126) 11 Telescopic handle 12 Hose guide with roller 13 Cable holder 14 Park fitting for fixing the hose during transport TempSpray - H326 / -H226...
DESCRIPTION OF UNIT TRANSPORT TempSpray-H326 and TempSpray-H226: TempSpray-H126: Roll up the high-pressure hose and fix to the hose guide park Roll up the high-pressure hose (roll diameter greater than 20 cm). fitting. Coil connecting hose over the cable holder and con- Then roll up the power cord as well.
TempSpray-H326 / -H226 / -H126 DESCRIPTION OF UNIT TECHNICAL DATA TEMPSPRAY-H326 TECHNICAL DATA TEMPSPRAY-H226 Voltage : 230 Volt ~, 50 - 60 Hz Voltage : 230 Volt ~, 50 - 60 Hz Fuses : 16 A Fuses : 16 A Power cord : 6 m long, 3x1.5 mm²...
TempSpray-H326 / -H226 / -H126 DESCRIPTION OF UNIT TECHNICAL DATA TEMPSPRAY-H126 Voltage : 230 Volt ~, 50 - 60 Hz Fuses : 16 A Unit connecting line : 4 m long, 3x1.5 mm² Max. current consumption : 2.6 A Degree of protection : IP 54 Max.
TempSpray-H326 / -H226 / -H126 STARTUP STARTUP 4.1.1 TEMPSPRAY-H326 AND TEMPSPRAY-H226 CONNECTION TO THE MAINS NETWORK Connection must always be carried out via 1. Place hose drum close to the Airless-unit. an appropriately grounded safety outlet with 2. Release hose whip (1) from frame and roll up the high- residual-current-operated circuit-breaker.
TempSpray-H326 / -H226 / -H126 STARTUP 4.2.1 TEMPSPRAY-H126 CONNECTION TO THE MAINS NETWORK 1. Mount the governor housing (1) to the hose connector of Connection must always be carried out via the airless-unit, thereby arrange the housing in a way that...
TempSpray-H326 / -H226 / -H126 STARTUP SWITCH-ON TempSpray - H126 Connect the heat controller to the mains supply. OFF appears in the display window (A) to indicate operational readiness. Press the START button (B), to switch the heat controller on. The display window changes from OFF to the preset tempera- ture of 40°C and the heating process begins.
(except water). folding. The risk of damage rises with the age of the high-pressure hose. Wagner recommends replacing high-pressu- Caution! Do not pump or spray in container re hoses after 6 years. with small opening (bunghole)! See safety regulations.
Before all repair work: Unplug the power plug from the outlet. Due to necessary custom tools repairs on the heating wire and the heating wire feed have to be done only by the Wagner- Service. A replacement of the heating-hose should, due to its internal heating wire, only be done from the Wagner-Service as well.
TempSpray-H326 / -H226 / -H126 REPAIRS AT THE UNIT TEMPSPRAY-H126 CHANGING THE POWER CORD Switch the unit off. Before all repair work: Unplug the power plug from the outlet. 1. Release cable connexion (1). 2. Remove protective covers (2). 3. Loosen all four screws (3) and carefully remove left hous- ing shell (4).
TempSpray-H326 / -H226 / -H126 REMEDY IN CASE OF FAULTS REMEDY IN CASE OF FAULTS DISPLAYED ERROR CODE POSSIBLE CAUSE MEASURES FOR ELIMINATING THE MALFUNCTION Err0 Residual current exceeded (approx. 33mA) and Please contact Wager Customer Service relay cuts out: •...
TempSpray-H326 / -H226 / -H126 SPARE PARTS AND ACCESSORIES 10.5 SPARE PARTS LIST TEMPSPRAY-H126 POS. ORTDER-NO DESIGNATION POS. ORTDER-NO DESIGNATION 9971 484 Round section cord (2) 9990 864 Cap (4) 2311 027 Housing part right 9905 115 Oval head screw D 3,17x16 (4)
4 weeks of the day of de- livery by the authorised specialist shop. Registration can be completed on the Internet under Wagner or one of our dealers will take back your used Wagner www.wagner-group.com/profi-guarantee. The guarantee certificate is valid as confirmation, as is the waste electrical or electronic equipment and will dispose of it for you in an environmentally friendly way.
Applied harmonised norms: are not original Wagner parts. EN 60519-1, EN 60519-2, EN 60204-1, EN 61000-3-2, for products to which modifications or additions have been EN 61000-3-3, EN 61000-6-1, EN 61000-6-3 carried out.