Replacing The Power Cable; Cleaning, Maintenance And Ordering Of Spare Parts; Carbon Brushes; Ordering Replacement Parts - EINHELL GE-SA 1435/1 Originalbetriebsanleitung

7. Replacing the power cable

Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
8.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.

8.2 Carbon brushes

In case of excessive sparking, have the carbon
brushes checked only by a qualifi ed electrician.
Danger! The carbon brushes should not be rep
laced by anyone but a qualifi ed electrician.
8.3 Maintenance
•
A worn out or damaged cutting unit should be
replaced by an authorised expert (see adress
on the warranty certificate).
•
Take care that all fastening elements (screws,
nuts, etc.) are firmly tightened, so that you
can work safely with the scarifier.
•
Store the scarifier in a dry place.
•
For longer life, all screw-fastened parts, such
as wheels and axles should be cleaned and
subsequently oiled.
•
Regular servicing of the scarifier not only
secures longer endurance and performance,
but also contributes to an accurate and simp-
le scarification of your lawn.
Anl_GE_SA_1435_1_SPK13.indb 22 Anl_GE_SA_1435_1_SPK13.indb 22
GB
•
At the end of the season, carry out a general
check of the scarifier, and remove all residue
collected. Before the start of every season, it
is absolutely necessary to check the state of
the scarifier. Contact our Customer Service
(see address on the warranty certificate) if
repair work is necessary.
The push bar has a P position (Fig. 15) in order
to take up less space during storage. To adopt
this position you must loosen the quick-release
levers by approx. 3 turns to allow for the higher
fastening in the parking position. With the bar in
this position, the scarifi er can be stood in a corner
in minimum space (Fig. 19). When you return the
bar to the working position, remember to tighten
the quick-release levers again by 3 turns!
8.4 Changing the roller (see Figures 20-23)
Be sure to wear work gloves!
Only replace the roller with a genuine Einhell rol-
ler, as this will ensure top performance and safety
under all conditions.
Proceed as follows to change the scarifi er roller or
the aerator roller:
Push the roller lock to the rear.
Lift the roller at this end and pull it out in the direc-
tion of the arrow (Fig. 21 + 22). Push the new roller
in the opposite direction onto the square-ended
drive. Then push the roller lock downwards (Fig 23).
Apply grease to the square-ended drive from time
to time so that the rollers can be changed easily.
If the cutting roller is positioned unfavorably, the
outer blade might be blocked by the housing. In
this case move the roller half a turn forward!

8.5 Ordering replacement parts:

Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.Einhell-Service.com
Replacement cutting roller Art. No.: 34.059.62
Replacement aerating roller Art. No.: 34.059.61
Optional catch basket Art. No.: 34.059.60
- 22 -
28.06.2022 08:53:04 28.06.2022 08:53:04