How To Unpack The Appliance; How To Transport The Appliance; Appliance Safety; Machine Safety - COMAC cacube 20 Bedienungs- Und Wartungsanleitung

HOW TO UNPACK THE MACHINE
The procedure for removing the device from its packaging is the following:
1. Open the outer carton box.
2. Remove the attachments inside from the carton box and lay them gently on the ground.
3. Take down the vacuum cleaner from the pallet with the help of a second person in order to avoid
damaging the machine.
N.B.: it is recommended that all the packaging components be kept for any future transportation
of the appliance.
CAUTION: users are advised to always wear protective gloves, to avoid the risk of serious injury
to hands.
HOW TO TRANSPORT THE MACHINE
The procedure for the safe handling of the device is the following:
1. Carry out the steps to secure the machine (read the paragraph "Securing the machine").
2. Remove the flexible hose (1) from the vacuum inlet (2) on the collection tank. Before pulling out the
flexible hose, press the button (3) to release the catch (Fig. 1).
3. Place the machine on the pallet and fasten the machine to the pallet using ropes or straps, making
them pass over the stem support..
4. Place the attachments inside the cardboard.
5. Close the carton box.
N.B.: For transportation in vehicles, secure the device according to the regulations in force so
that it can not slide or tip over.
CAUTION: users are advised to always wear protective gloves, to avoid the risk of serious injury
to hands.
3
2
1
1

MACHINE SAFETY

The stages for making the appliance safe, thereby making it possible to carry out operations safely,
are as follows:
1. Check that both general switche is disabled, if not set them to.
2. Make sure that the plug on the power cable has been taken out of the mains supply socket, and if
not, disconnect it (Fig.2).
3. Wind the power cable.
CAUTION: We recommend handling the power cable with dry hands to avoid serious injury.
CAUTION: To prevent damaging the power cable, disconnect the plug from the mains socket by
directly pulling the plug and not the cable.

PREPARING THE MACHINE

Before you start working you need to do the following:
1. Check the main switch is turned off, otherwise turn it off.
2. Check that the plug in the power supply cable is disconnected from the mains socket, otherwise
disconnect it.
WARNING: To avoid damage to the power cable, disconnect the plug from the mains socket by
pulling the plug directly instead of the cable
3. Remove the cover (1) before removing the cover, loosen the retaining hooks (2) located at the side
of the collection shaft (3 (Fig. 1).
4. Check the fabric filter (4) is correctly positioned (Fig. 4).
1
2
3
1
N.B. : For dry use, we recommend that you check that the inside of the collection tank has
been drained of all liquids before use.
N.B: If cartridge filters or dust collection bags are used instead of the cloth filter, make sure
they are positioned correctly.
5. Refit the suction cover 1 above the collection drum,
6. Remember to attach it to it using the retaining hooks.
7. Before use, check the regular status and service safety of the
appliance with the working equipment, especially the power cord and
the extension cable. If the state is not perfect, the use of the appliance
is prohibited.
To vacuum dry objects, do as follows:
1. Insert the vacuum hose (1) from the vacuum nozzle (2) on the collection tank, before pulling the
vacuum hose press the button (3) for unlocking the catch (Fig.1).
2. Select the most suitable accessory for the work to be carried out. Insert the selected accessory into
the vacuum hose, if necessary also use the extension tubes.
3. Insert the plug of the power supply cable in the mains supply socket.
ATTENTION: Do not exceed the maximum mains impedance value allowed for the electrical
doubts concerning mains impedance on the connecting point.
CAUTION: Do not insert the power cable into the socket of the mains plug with wet hands.
4. Switch on the machine by setting the main switch (4) to "I"
5. Start work.
WARNING: danger of damage! If you aspire to dry, never remove the cloth filter during suction.
(optional component).
2
1
1
If during work you notice that the suction power is reduced or the noise of the unit becomes stronger:
• Switch off the appliance, turn the main switch (4) to the resting position (Fig. 2).
• Beat the filter using the knob (7) in (Fig. 2) moving up and down, if this operation is not sufficient.
• Remove the plug from the power supply cable from the mains socket.
WARNING:To avoid damage to the mains socket, disconnect the mains plug from the mains
6. Remove the suction cover (2), Before removing the lid, loosen the retaining latches (5) located at
the side of the collection drum and Disconnect the Flex (4) from the sleeve above the cover (Fig.
4) and lay it on the ground.
7. Remove the Fabric filter (6) from the inside of the keg, shake and clean the fabric filter. (Fig. 3)
8. Empty the collection drum.
9. Repeat the operations backwards to return to work.
NOTE: If the filter surface is extremely dirty, it is advisable to brush the filter to thoroughly clean
NOTE: The place used for this operation must comply with the standards in force for the
NOTE: If the previous operations have not solved the low suction switch off the machine and
3
6
4
4
18

WORK

VACUUMING DRY OBJECTS
connection point (see Technical Data). Please contact your electrical energy supplier if in
The suction of fine dusts replace the cloth filter with the most suitable cartridge filter
7
2
3
socket by pulling the plug directly instead of the power cord.
it with a normal soft brush.
environment.
remove the obstruction from the suction pipe or from the accessory you are using.
5
5
4
4
4
2