Making Cuts With The Bandsaw In Stationary Mode (Fig. 18/19) - EINHELL TE-MB 18/127 U Li Originalbetriebsanleitung

If the battery pack fails to charge, check for the
following:
•
voltage at the power socket
•
whether there is good contact at the charging
contacts of the charging unit
If the battery pack still fails to charge, send
•
the charger and charging adapter
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
6.2 Battery capacity indicator (Fig. 15/Item 9)
Press the battery capacity indicator switch (a).
The battery capacity indicator (9) shows the char-
ge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
6.3 On/Off switch (Fig. 16)
•
Press the safety lock-off (5) in order to release
the On/Off switch (3).
Anl_TE-MB_18_127_U_Li_SPK13.indb 26 Anl_TE-MB_18_127_U_Li_SPK13.indb 26
GB
•
Actuate the On/Off switch (3).
•
Important! You can let go of the safety lock-
off (5) as soon as the On/Off switch (3) was
actuated.
•
To switch off the saw, let go of the On/Off
switch (3) again.
6.4 Making cuts with the bandsaw in hand-
guided mode (Fig. 17)
•
The bandsaw is used without the base frame
(24). Remove the base frame (24) if necessa-
ry (see 5.6.1).
•
Set the adjustable handle (10) as described in
section 5.2.
•
Set the workpiece stop (13) as described in
section 5.3.
•
The material you want to cut must be clamped
securely.
•
Hold the machine firmly with both hands; use
the one hand on the handle (1) and the other
hand on the adjustable handle (10).
•
Take care to maintain a steady foothold.
•
Switch on the bandsaw as described in sec-
tion 6.3.
•
Move the bandsaw with its blade (15) in front
of the workpiece.
•
First place the workpiece stop (13) against
the workpiece and align the blade with the
cutting plane.
•
Now guide the bandsaw with a firm grip to the
workpiece and cut into it carefully.
•
Important! Do not exert excessive pressure on
the blade! This way you will obtain the straigh-
test possible cut while also prolonging the life
of the blade.
•
Do not cut any cross-sections larger than tho-
se described in section 4. Technical data.
•
Warning! If you are unable to cut through the
workpiece in a single pass, there will be a
greater risk of the blade getting jammed and
causing kickback!
6.5 Making cuts with the bandsaw in stationa-
ry mode (Fig. 18/19)
•
The bandsaw is used with the base frame
(24). Mount the base frame (24) if necessary
(see 5.6.1).
•
Place the base frame on a level surface where
it can stand firmly.
•
Set the desired angle as described in section
5.6.3.
•
Caution! Depending on the set angle, the cut-
ting width or the cutting height might become
smaller. (See 4. Technical data)
•
Use the pushlock button (26) to lock the
- 26 -
15.09.2022 11:08:29 15.09.2022 11:08:29