EINHELL TE-MB 18/127 U Li Originalbetriebsanleitung Seite 25

•
Use the 3 socket head screws (35) to fasten
the bandsaw to the mounting arm (25). Do
this with the hex key (23).
•
Important! The mounting arm (25) and the
bandsaw must engage with each other in a
positive fit.
5.6.2 Adjusting the pushlock button (Fig. 10)
•
The bandsaw is set at the factory in transport
position and locked in bottom position.
•
To unlock the pushlock button (26) proceed
as follows:
1. Pull out the pushlock button (26) and hold it
there.
2. Turn the pushlock button counter-clockwise
as far as the stop.
3. Let go of the pushlock button.
•
The pushlock button (26) must be unlocked in
order to be able to carry out any cuts.
•
The bandsaw can also be locked in top posi-
tion in addition to transport position. This set-
ting is used, for example, when carrying out
cleaning jobs or clamping the workpiece.
5.6.3 Setting angles on the base frame
(Fig. 11)
•
Angle cuts from 0 to 45° can be carried out
using the base frame (24).
•
Undo the locking lever (31) by moving it
counter-clockwise.
•
Important! By changing the position you can
readjust the pretension of the clamping lever
(31). Proceed as follows:
- Pull up the clamping lever (31) and hold it
there.
- You can now rotate the clamping lever wit-
hout changing the tension.
- Let go of the locking lever (31) again.
•
Turn the mounting arm (25) to the required
angle.
•
Then re-tighten the clamping lever (31).
5.6.4 Precision adjustment of the angle scale
(Fig. 8/11)
•
You can readjust the angle indicator if requi-
red. To do so you will need a 90° stop angle
(not included with this product).
•
Slacken the clamping lever (31).
•
Place a 90° stop angle between the fixed
clamping jaw (28) and the blade (15).
•
Turn the mounting arm (25) to the point where
the angle between the fixed clamping jaw (28)
and the blade (15) equals exactly 90°.
•
Tighten the clamping lever (31) in order to
secure this setting.
Anl_TE-MB_18_127_U_Li_SPK13.indb 25 Anl_TE-MB_18_127_U_Li_SPK13.indb 25
GB
•
Then undo the recessed head screw (33)
using a screwdriver (not included with this
product).
•
Adjust the pointer (32) to position 0° on the
angle scale (34).
•
Finally, secure this setting by tightening the
recessed head screw (33).
5.6.5 Clamping the workpieces (Fig. 12)
•
To clamp a workpiece in the base frame (24)
you must first release the movable clamping
jaw (27) by turning the handle (29) counter-
clockwise.
•
For small adjust widths: Turn out the handle
(29) to the point where the workpiece can be
inserted between the fixed clamping jaw (28)
and the movable clamping jaw (27).
•
For large adjust widths: Swing up the quick-
adjust facility (30). You can then use the
handle (29) to pull out or push in the movable
clamping jaw (27).
•
Then swing the quick-adjust facility (30) back
down again in order to be able to clamp the
workpiece.
•
Clamp the workpiece by turning the handle
(29) clockwise.
•
Caution! Long workpieces must be secured
against falling off at the end of the cutting
operation. You can use, for example, a roller
stand or similar.
6. Operation
6.1 Charging the Li battery pack (Fig. 13/14)
1. Remove the battery pack (6) from the handle,
pressing the pushlock button (8) downwards
to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(7) into the mains socket outlet. The green
LED will then begin to fl ash.
3. Push the battery pack onto the battery char-
ger.
In section 10 (Charger indicator) you will fi nd a
table with an explanation of the LED indicator on
the charger.
- 25 -
15.09.2022 11:08:28 15.09.2022 11:08:28