EINHELL TE-MB 18/127 U Li Originalbetriebsanleitung Seite 24

the machine's moving parts run smoothly.
•
Important! The two hex keys (22/23) are
stored in the adjustable handle (10) (see Fig.
2).
•
Important! Please note that the tooth pitch of
the blade you are using must match the mate-
rial you want to cut. In the case of particularly
hard materials or particularly large depths
of blade penetration you should change the
tooth pitch by changing the blade.
5.2 Adjusting the handle (Fig. 3)
•
The adjustable handle (10) can be fastened
in various locking positions according to re-
quirements.
•
Release the clamping lever (11).
•
Place the adjustable handle (10) in the requi-
red position.
•
Lock the setting by refastening the clamping
lever (11).
•
Important! You can adjust the pretension of
the clamping lever (11). To do so, hold the
released clamping lever (11) firmly and adjust
the nut (12) on the opposite side (clockwise:
higher tension). Check the setting by closing
the clamping lever (12) again. Keep repeating
until you have the required tension.
5.3 Adjusting the workpiece stop (Fig. 4)
•
Important! The workpiece stop (13) is set at
the factory to bottom position.
•
Caution! When you use the cordless bandsaw
together with the base frame (24), the workpi-
ece stop (13) must be set to bottom position.
•
Caution! When you work without the base
frame (24), the workpiece stop (13) should
also be set to bottom position because this
will increase the size of the guide face. Set
the workpiece stop to a higher position only in
exceptional cases.
•
Slacken the two socket head screws (14)
with the hex key (22) in order to be able to
push the workpiece stop (13) to the required
position. Then retighten the two socket head
screws (14).
5.4 Information about the LED lamp (Fig. 1)
•
The machine has an LED lamp (4) for illumi-
nating the cutting area.
•
As soon as you press the On/Off switch (3),
the LED lamp (4) will come on automatically.
•
A few seconds after you release the On/Off
switch (3) again, the LED lamp (4) will switch
off automatically.
Anl_TE-MB_18_127_U_Li_SPK13.indb 24 Anl_TE-MB_18_127_U_Li_SPK13.indb 24
GB
5.5 Fitting/removing the blade (Fig. 5 – 7)
•
Before you change the blade: Remove the
battery!
•
Wear work gloves to prevent injury when
changing the blade.
•
Slacken the blade (15) by turning the clam-
ping lever (16) clockwise.
•
To remove the blade: start at the top part of
the blade guard (17), then continue around
the blade pulleys (18) and finish at the guide
rollers (20).
•
Caution! When the blade is being removed,
the tension might be released with a jerk
causing the blade (15) to jump off the blade
pulleys (18)!
•
Before you mount the new blade, clean the
guide rollers (20) and the two blade pulleys
(18). Make sure in particular that the rubber
tire (19) is free of chips.
•
Caution! A damaged rubber tire (19) must be
replaced immediately.
•
Mount the new blade (15) in reverse order
beginning at the guide rollers (20).
•
Caution! Pay attention to the running direc-
tion. The cutting angle of the teeth must point
in running direction, i.e. towards the workpie-
ce stop (13). (See the arrow on the two blade
pulleys (18)).
•
Make sure that the new blade (15) runs freely
in the guide rollers (20) and in the upper bla-
de guard (17).
•
Tension the blade (15) by turning the clam-
ping lever (16) counter-clockwise.
•
Important! The blade must first be run in.
Switch on the machine briefly and check how
the blade is running. Check that the blade is
running correctly before you start cutting.
•
Important! The width of the new blade must
be at least as large as stipulated in section
4. Technical data. The teeth of the blade (15)
must project beyond the guide rollers (20)
(see Fig. 7b). If the new blade (15) is too nar-
row, the teeth will be damaged and the blade
will become blunt.
5.6 Bandsaw with base frame (Fig. 1a, 8)
5.6.1 Mounting / removing the bandsaw on /
from the base frame (Fig. 9)
•
Unlock the pushlock button (26) (see 5.6.2)
and turn the mounting arm (25) downwards.
•
Place the bandsaw on the base frame (24) so
that the workpiece stop (13) rests on the base
frame and the holes in the mounting arm (25)
lie above the threaded holes in the bandsaw.
- 24 -
15.09.2022 11:08:28 15.09.2022 11:08:28