Inhaltsverzeichnis
Werbung
English
ORBITAL SANDER SAFETY WARNINGS
CAUTION
Prior to the sanding operation, make sure the material
you are going to sand.
If generation of harmful/ toxic dusts such as lead
paint, woods and metals is expected under the
sanding operation, make sure the dust bag or
appropriate dust extraction system is connected with
dust outlet tightly.
SPECIFICATIONS
Model
Voltage (by areas)*
Power Input
No-load speed
Diam. of Orbit
Sanding pad size
Sanding paper size
Weight (without cord)
*Be sure to check the nameplate on product as it is subject to change by areas.
STANDARD ACCESSORIES
Sanding paper ............................................................ 1
Dust bag (for model SV12V, SV12SD) ...................... 1
Standard accessories are subject to change without
notice.
OPTIONAL ACCESSORIES (sold separately)
1. Sanding paper
Perforated sanding paper for model SV12V, SV12SD
Non-perforated sanding paper for model SV12SE
Grain: AA40, AA60, AA80, AA100, AA120, AA150,
AA180, AA220, AA240
(1) Standard Type (Perforated or non-Perforated), 114 ×
280 mm
(2) Pressure Sensitive Type (Perforated or non-
Perforated), 114 × 228 mm
2. Magic Pad (Pressure Sensitive Type), 114 × 228 mm
(1) Perforated Pad (for model SV12V, SV12SD)
(2) Non-Perforated Pad (for model SV12SE)
3. Cleaner Adaptor (for model SV12V, SV12SD)
4. Punch plate (for model SV12V, SV12SD)
Optional accessories are subject to change without notice.
APPLICATIONS
Finish polishing of woodwork surfaces
Sanding surfaces of woodwork or sheet metal prior
to painting, etc.
7
Wear the dust mask additionally, if available.
Do not inhale or touch the harmful / toxic dusts
generated in sanding operation, the dust can
endanger the health of yourself and bystanders.
SV12V
(110V, 115V, 120V, 127V, 220V, 230V, 240V)
4000 - 10000min
–1
114 mm × 228 mm
114 mm × 280 mm
2.8 kg
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF positon. If
the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.
3. Extension cord
When the work area is remote from the power source,
use an extension cord of sufficient thickness and
rated capacity. The extension cord should be kept as
short as practicable.
4. Attaching sanding paper
(Start at Switch handle's side)
(1) Open paper holder by turning the clamping lever
(Fig. 1).
(2) Place the sander as shown in Fig. 2 Insert the sanding
paper between the paper holder and the bottom plate
until it can go no further.
(3) Match the width of the sanding paper with the width
of the pad.
Return the clamping lever to its original position to
secure the sanding paper.
(4) When using perforated sanding paper.
To secure the other end of the sanding paper, pull the
sanding paper while aligning the holes of the sanding
paper with the holes of the pad.
(5) When using non-perforated sanding paper.
Align the sanding paper on the pad and pull the
sanding paper to secure the other end.
SV12SD
SV12SE
300W
10000min
–1
2.4 mm
2.8 kg
2.6 kg
Werbung
Inhaltsverzeichnis
