Connection To An External Dust Extraction System - Scheppach 5901223901 Original Bedienungsanleitung

• Push in the locking pin (23) to fix it in the unlocked
position.
• Swivel the machine head (4) upwards.
• The clamping device (7) can be attached to both
sides of the fixed saw table (15). Insert the clamp-
ing device (7) into the holes provided for them on
the rear side of the stop rail (16) and secure it with
the star grip screws (7a). For miter cuts 0°- 48°, the
clamping device (7) must be mounted on the oppo-
site side of the saw head.
• The machine head (4) can be tilted to the left and to
the right to max. 50° by loosening the locking screw
(22). To do this, pull out the safety bolt for swiveling
function (36) and swivel the machine head.
• Workpiece supports (8) must always be secured and
used during work. Define the desired size of the ta-
ble, by opening the locking lever (9). Then tighten
the locking lever (9) again.
8.2 Dust bag (fig. 1/21)
The saw is equipped with a dust bag (17) for chips.
Attach the dust bag (17) to the outlet opening in the
motor area.
The dust bag (17) can be emptied via the zip on the
underside.
8.2.1 Connection to an external dust extraction
system
• Connect the suction hose to the dust extraction.
• The dust extraction system must be suitable for the
material to be processed.
• Use a special extraction device to extract dusts that
are particularly harmful to health or carcinogenic.
8.3 Fine adjustment of the stop for 90° chop cut
(fig. 1/2/5/6)
Tool required:
- Allen key, 6 mm
• Stop bracket not included in the scope of delivery.
• Lower the machine head (4) and fix it with the locking
pin (23).
• Loosen the locking screw (22).
• Place the stop bracket (A) between the saw blade (6)
and the rotary table (14).
• Adjust the adjustment screw (26) until the angle be-
tween the saw blade (6) and the rotary table (14) is
90°.
• Then check the position of the angle display. If nec-
essary, loosen the pointer (19) with a Phillips screw-
driver, set the scale (18) to 0° position and re-tighten
the retaining screw.
8.4 Fine adjustment of the stop for 45° mitre cut
(fig. 1/2/5/9/10)
Tool required:
- Allen key 5 mm (not included in the scope of deliv-
ery)
- Open-ended spanner SW10 (not included in the
scope of delivery)
• Stop bracket not included in the scope of deliv-
ery.
• Lower the machine head (4) and fix it with the locking
pin (23).
• Fix the rotary table (14) in the 0° position.
Attention!
For mitre cuts (inclined saw head), the moveable
stop rail (16a) must be fixed in the outer position.
• Loosen the locking screw (16b) on the moveable
stop rails (16a) and push the moveable stop rails
(16a) outwards.
• The moveable stop rails (16a) must be locked in a
position that the distance between the stop rails
(16a) and the saw blade (6) is at least 8 mm.
• The moveable stop rail (16a) must be in the inner
position.
• Before making the cut, check that no collision could
occur between the stop rails (16a) and the saw blade
(6).
• Loosen the locking screw (22) and tilt the machine
head (4) to the left, to 45°, using the handle (1).
• Place 45° stop bracket (B) between saw blade (6)
and rotary table (14).
• Loosen the counternut (27a) and the adjustment
screw (27) until the angle between the saw blade (6)
and the rotary table (14) is exactly 45°.
• Tighten the counternut (27a) again.
• Then check the position of the angle display. If nec-
essary, loosen the pointer (19) with a Phillips screw-
driver, set the scale (18) to 45° position and re-tight-
en the retaining screw.
• Repeat this process to set the 45° position on the
right side.
www.scheppach.com GB | 33