Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
STEP 3
Assembling of the connection cable (34) to the sensor
cable (38) and installation of support (30) at the main
frame (40).
1. Place screws M8x15 (33), curved washers (31) and spring
washers (32) accessibly beside the front part of the main
frame (40).
2. Place the lower end of the support (30) against the main
frame (40) and push the rubber ring (100) and support cover
(101) onto the support (30).
3. Plug the ends of the two computer cables (34-38)
projecting from (30+40) together. (Note: The connection
cable (34) projecting from the support (30) must not slide into
the tube, as it is required for later steps of installation.) When
joining the tubes, ensure that the cable connection will not
trapped.
4. Connect the middle section tension cable (39) to the
bracket of lower section cable tension (35) (See figure A1-A3).
Before this step of the installation, it is advisable to adjust the
resistance setting to the lowest stage 1, at which the cable
extends furthest from the sheath. Put the lowest part of cable
(39) into the small hook (figure A1). Pull it until the small hook
get in higher position (A2) and then insert the cable (39) onto
the bracket (35) (figure A3).
5. Put one spring washer (32) and one curved washer (31) on
each screw (33). Push the screws (33) through the holes in the
support (30), screw into the threaded holes of the main frame
(40) and tighten lightly.
6. Push the plastic cover (101) and rubber ring (100) into the
right position to cover the connection point.
STEP 4
Installation of handgrips (5), footrest holder (44) and
connecting tubes (25).
1. Push the handgrip bars (5R) onto the connecting tubes
(25R) and adjust the holes in the tubes so that they are
aligned. (Note: the handgrip bars must be aligned after as-
sembly so that the upper ends are inclined outwards (away
from the support (30)).
2. Push the screws M8x20 (66) through the holes and
tighten the handgrip bars (5) with curved washers (31) and
spring washer (32) firmly.
3. Put the footrest holder (44R) at the connecting tube (25R)
and adjust the holes in the tubes so that they are aligned.
4. Push the screw M8x78 (23) through the holes and tighten
the footrest holder (44R) at connection tube (25R) with wash-
ers (27) and nut (26) firmly. (This connection point has to move
easily. So please don't tighten the screw too much.)
5. Place the preassembled unit of the right footrest holder
(44R) and connecting tube (25R) at the right hand side of the
main frame (40). (Note: Right is specified as viewed standing
on the machine during training.)
6. Push the grip axle (19) into the middle position at handle-
bar support (30) and put one wave washer (20) and the con-
necting tube (25R) onto the axles' end (19). Put on the hex
screw M8x20 (12) a spring washer (32) and a washer 8//32
(22) and tighten it firmly.
7. Put the foot pedal holder (44R) at the pedal crank (97) and
tighten them with steel tube (52), washer 8//20 (49), spring
washer (32) and screw M8x20 (48) firmly.
8. Install the left footrest holder (44L) incl. all additionally
required parts on the left hand side of the machine as
described in 1. – 7.
9. Put the plugs of pulse cables (10) into the plugs from pulse
connection cables (16) and attach the screw caps (11) onto
screws (12).
A1
119
119
11
12
120
32
22
44L
40
97
17
A2
A3
39
35
31
33
32
34
38
35
40
5L
31 32
66
30
20
25L
19
26
27
32
48
52
49
GB
30
100
101
39
5R
25R
44R
23
Werbung
Inhaltsverzeichnis
