Cleaning And Care; Technical Data - VOLTCRAFT DS-50S Bedienungsanleitung

3. Press TARE. The display will show the value "0.0".
4. Place the object to be weighed into the measuring container.
à
The weight shown will be the net weight of the object you are weighing.
à
To continue weighing without the measuring container, remove the container from the
weighing surface and press TARE.
5. Press ON/OFF to turn the power OFF.
8.3 Counting
This function determines the quantity of equal weight objects in batches.
1. Press ON/OFF to turn the power on.
2. Place (25, 50, 75 or 100) objects on the weighing platform.
3. Press and hold PCS until the number "25" appears on the display.
4. Press MODE repeatedly to set a reference unit number (25, 50, 75 or 100).
5. Press PCS. The display will show the number of units.
6. Add or remove objects from the weighing platform.
7. Press MODE to return to normal weighing mode.
à Press HOLD to lock a readout for 30 secs, or press hold again to cancel the hold.
8.4 Calibration
The scale was calibrated at the factory. If accuracy fails, first try replacing the batteries.
Preconditions:
a
A standard test weight of 5000 g or 10000 g is required for calibration.
a
The weighing platform must be empty.
1. Press ON/OFF to turn the power on.
2. Press and hold MODE until the display shows capacity "50000 g", then press MODE
again. The display will show "5000 g."
3. Press TARE to select a test weight or 5000 g or 10000 g.
4. Press MODE to select the weight. The display will alternate between "CAL" and the se-
lected weight.
5. Place the selected test weight on the weighing platform.
à Calibration is completed when "PASS" appears on the display. This may take a few
moments.
à
If a calibration error has occurred, "Err" will show on the display. Switch the power
ON/OFF and then repeat the process.
6. Remove the weight.
7. Press ON/OFF to turn the power OFF.
9 Disposal
9.1 Product
This symbol must appear on any electrical and electronic equipment placed on
the EU market. This symbol indicates that this device should not be disposed of
as unsorted municipal waste at the end of its service life.
Owners of WEEE shall dispose of it separately from unsorted municipal waste.
Spent batteries and accumulators, which are not enclosed by the WEEE, as well
as lamps that can be removed from the WEEE in a non-destructive manner, must
be removed by end users from the WEEE in a non-destructive manner before it is
handed over to a collection point.
Distributors of electrical and electronic equipment are legally obliged to provide free take-
back of waste. Conrad provides the following return options free of charge (more details on
our website):
■
in our Conrad offices
■
at the Conrad collection points
■
at the collection points of public waste management authorities or the collection points
set up by manufacturers or distributors within the meaning of the ElektroG
End users are responsible for deleting personal data from the WEEE to be disposed of.
It should be noted that different obligations about the return or recycling of WEEE may apply
in countries outside of Germany.
9.2 (Rechargeable) batteries
Remove batteries/rechargeable batteries, if any, and dispose of them separately from the
product. According to the Battery Directive, end users are legally obliged to return all spent
batteries/rechargeable batteries; they must not be disposed of in the normal household
waste.
Batteries/rechargeable batteries containing hazardous substances are labelled
with this symbol to indicate that disposal in household waste is forbidden. The
abbreviations for heavy metals in batteries are: Cd = Cadmium, Hg = Mercury,
Pb = Lead (name on (rechargeable) batteries, e.g. below the trash icon on the
left).
Used (rechargeable) batteries can be returned to collection points in your municipality, our
stores or wherever (rechargeable) batteries are sold. You thus fulfil your statutory obligations
and contribute to environmental protection.
4
Batteries/rechargeable batteries that are disposed of should be protected against short cir-
cuit and their exposed terminals should be covered completely with insulating tape before
disposal. Even empty batteries/rechargeable batteries can contain residual energy that may
cause them to swell, burst, catch fire or explode in the event of a short circuit.

10 Cleaning and care

Important:
– Do not use aggressive cleaning agents, rubbing alcohol or other chemical solutions.
They damage the housing and can cause the product to malfunction.
– Do not immerse the product in water.
1. (If applicable) disconnect the product from the power supply.
2. Clean the product with a dry, fibre-free cloth.

11 Technical data

Power supply ................................. 3x 1.5 V AAA batteries
Capacity.......................................... max. 50 kg
Accuracy......................................... ±8 g
Units ............................................... kg:g, lb, oz, lb:oz
Graduation...................................... 1 g
Weighing platform........................... Stainless steel
Auto power off ................................ 285 seconds
Operating / storage conditions........ +5 to +35 °C, 20 - 80 % RH (non-condensing)
LCD (W x H) ................................... 75 x 30 mm
Dimensions (W x H x D) (approx.).. 180 x 38 x 260
Weight (approx.)............................. 1105 g (without batteries)
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming or the capture in
electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.
This publication reflects the technical status at the time of printing.
Copyright by Conrad Electronic SE.
*2490613_V4_0422_dh_mh_en 9007199693134219-2 I2/O4 en
5 - 6 V/DC, max. 1.0 A