Description Of The Machine; Machine Parts And Labels; Ptional Kits; Accessories - Nilfisk T75 Betriebsanleitung

Description of the machine

Machine Parts and Labels

Figure 1
Identification plate w ic includes
1.
Code of the Model, Technical Data (see table on page 6),
Serial N ., Mark,
network volta e.
2. Vacuum union hose
3. Control panel
4. Vacuum gauge
5. Dust container
6. Filter chamber
7. Outlet
arnin plate
8.
raws t e operator s attention to t e act t at t e filter
must only e s aken w en t e vacuum cleaner is turned
FF see also par. Primary filter s aker .
9. Panel power plate
Indicates that the panel is powered by the voltage
indicated on the data plate.
10. Vacuum inlet
11. Accessories compartment
The access to the panel is allowed to specialized personnel only
who, before touching the electrical equipment, must disconnect
the machine from its power source by turning the main switch
to 0 - o and y removin t e plu
T is mac ine creates a stron air ow w ic is drawn in t rou
the vacuum inlet and blows out through the outlet.
e ore turnin on t e mac ine, fit t e vacuum ose into t e
inlet and t en fit t e re uired tool on to t e end part re er to t e
manufacturer's accessory catalogue or Service Centre).
The diameters of the authorized hoses are indicated in the
Technical data table.
T e mac ine is e uipped wit a primary filter w ic ena les it
to be used for the majority of applications.
In addition to t e primary filter t at retains t e most common
dust, a secondary filter a solute filter can e installed.
T is mac ine is e uipped wit an internal a e plate w ic
subjects the vacuumed substances to a circular centrifugal
movement t at makes t em drop into t e container.
Optional kits
Various optional kits are availa le or convertin t e mac ine.
n re uest, t e mac ine can e supplied wit optional kits
already installed. owever, t ey can also e installed at a later
date.
Please contact t e sales network or urt er details.
Instructions descri in ow to fit t e optional kits and t e
relative operation and maintenance manuals are supplied
to et er wit t e optional kits.
ear o manu acture, Nominal
rom t e electrical socket.
CAUTION!
Use only supplied and authorised genuine spare parts.

Accessories

Various accessories are available; refer to the manufacturer's
accessory catalogue.
CAUTION!
Use only genuine accessories supplied and authorised
by the manufacturer.
Packing and unpacking
All t e dispatc ed e uipment as een t orou
before being delivered to the haulage contractor.
n arrival, c eck t e mac ine to see t at it
damaged during transport. If this is the case, immediately
lodge a complaint with the haulage contractor.
ispose o t e packin materials in compliance wit t e laws
in force.
Model A (mm)
T75 1850
ei t wit packin
(*)
Unpacking, moving, use and storage
To unpack t e vacuum unit, remove t e retainers wit
hammer and a screwdriver.
Also remove the fastening devices placed by the manufacturer
w en packin , y usin suita le tools.
elease t e w eel rakes and remove t e mac ine rom t e
supporting platform, by using a ramp that can provide adequate
capacity, and by driving the vacuum cleaner by the handle.
perate on at, ori ontal sur aces.
The load-bearing capacity of the surface the machine is placed
on must be suitable for bearing its weight.
I t e device is to work in a fixed position, allow wide space
around the device in order to ensure freedom of the movement
and allow t e maintenance sta to operate wit ease.
CAUTION!
The manufacturer shall not be liable for any damages
caused to the machine during lifting, when the lifting
equipment supplied by the manufacturer is not used.
5
ly c ecked
as not
Figure 2
B (mm) C (mm) kg (*)
1350 700 220
T75
een
a
GB
C360