Herunterladen Inhalt Inhalt Diese Seite drucken

Operation - DeWalt XR LI-IONDCS320 Originalanweisungen

Akku-säbelsägen
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 19
2. Slide it into the handle until the battery pack is
firmly seated in the tool and ensure that it does
not disengage.
TO REMOVE THE BATTERY PACK FROM THE TOOL
1. Press the battery release button (g) and firmly
pull the battery pack out of the tool handle.
2. Insert battery pack into the charger as
described in the charger section of this manual.
FUEL GAUGE BATTERY PACKS (FIG. 2)
Some D
WALT battery packs include a fuel gauge
E
which consists of three green LED lights that
indicate the level of charge remaining in the battery
pack.
To actuate the fuel gauge, press and hold the fuel
gauge button (i). A combination of the three green
LED lights will illuminate designating the level of
charge left. When the level of charge in the battery
is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
NOTE: The fuel gauge is only an indication of the
charge left on the battery pack. It does not indicate
tool functionality and is subject to variation based
on product components, temperature and end-user
application.
Variable Speed Trigger Switch
(fi g. 4)
LOCK-OFF BUTTON AND TRIGGER SWITCH
Your saw is equipped with a lock-off button (b).
To lock the trigger switch, press the lock-off
button as shown in figure 4. Always lock the trigger
switch (a) when carrying or storing the tool to
eliminate unintentional starting. The lock-off button
is colored red to indicate when the switch is in its
unlocked position.
To unlock the trigger switch, press the lock-off
button as shown in figure 4. Pull the trigger switch
to turn the motor ON. Releasing the trigger switch
turns the motor OFF.
WARNING: This tool has no provision
to lock the switch in the ON position,
and should never be locked ON by any
other means.
The variable speed trigger switch will give you added
versatility. The further the trigger is depressed the
higher the speed of the saw.
CAUTION: Use of very slow speed is
recommended only for beginning a cut.
Prolonged use at very slow speed may
damage your saw.

OPERATION

WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.
Blade Installation and Removal
(fi g. 1, 5–7, 10)
Different blade lengths are available. Use the
appropriate blade for the application. The blade
should be longer than 89 mm (3-1/2") and should
extend past the shoe and the thickness of the
workpiece during the cut. Do not use jigsaw blades
with this tool.
WARNING: Cut hazard. Blade
breakage may occur if the blade
does not extend past the shoe and
the workpiece during the cut (fig. 5).
Increased risk of personal injury, as well
as damage to the shoe and workpiece
may result.
TO INSTALL BLADE INTO SAW
1. Pull blade clamp release lever (c) up (fig. 1).
2. Insert blade shank from the front.
3. Push blade clamp release lever down.
NOTE: The blade can be installed in four positions
as shown in figure 6. Both units allow the blade to
be installed upside-down to assist in flush-to cutting;
see figure 10.
TO REMOVE BLADE FROM SAW
CAUTION: Burn hazard. Do not touch
the blade immediately after use. Contact
with the blade may result in personal
injury.
1. Open up blade clamp release lever.
2. Remove blade.
Proper Hand Position (fi g. 9)
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the hand
grip (e), with the other hand on the main handle (h).
EN GL IS H
39

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Xr li-ion dcs380

Inhaltsverzeichnis