Saw Blades; Operation - DeWalt DWE397 Originalanweisungen

EN GLI SH
5. Close the gearcase cap (l) and tighten the
gearcase cap screw.
WARNING: Before operation let the
saw blades run freely for approx. 20 s.

Saw Blades

Cat. No. Material
to be cut
DWE396 Rough wood
Fine wood
Fine wood
Low density building block
Medium density building block TCT T20 DT2977
DWE397 Rough wood
Low density building block
Medium density building block TCT T20 DT2976
Insulation materials
Celluar contrete
DWE398 Rough wood
Low density building block
Medium density building block TCT T20 DT2976
Insulation materials
Celluar contrete
DWE399 Rough wood
Low density building block
Medium density building block TCT T20 DT2976
Insulation materials
Celluar contrete
Prior to Operation (fi g. 1)
• Mount the appropriate type of saw blade.
• Check that the tool is running properly and can
perform all its functions. Make sure that the bar
(f) is still straight and the saw blades (e) and the
housing are undamaged.

OPERATION

Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.
WARNING:
• Ensure the material to be sawn is
secured in place.
28
Recommended
saw blade type
HSS DT2970
HSS DT2971
Proper Hand Position (fi g. 1, 6)
TCT DT2972
TCT T12 DT2973
HSS DT2978
TCT T12 DT2974
HSS DT2979
TCT 12 DT2975
Proper hand position requires one hand on the
HSS DT2978
front handle (d) with the other hand on the rear grip
TCT T12 DT2974 handle (c).
Switching On and Off (fi g. 1)
HSS DT2979
TCT 12 DT2975
For safety reasons the ON/OFF switch (a) is
equipped with a lock-off button (b).
HSS DT2978
TCT T12 DT2974
1. Push the lock-off button (b) to unlock the tool.
2. To run the tool, press the ON/OFF switch (a).
HSS DT2979
As soon as the ON/OFF switch is released the
TCT 12 DT2975 lock-off switch is automatically activated to
prevent unintended starting.
3. Always switch off the tool before unplugging.
Sawing (fi g. 1, 3, 4, 6)
For long, straight cuts first draw a line on the
workpiece and follow the line.
Make downward cuts only. Avoid cutting earth as
this will blunt the saw blades very quickly.
When using a saw horse always cut on the outside
of the saw horse arms.
1. Clamp the workpiece on one side only to
prevent the bar from jamming in the workpiece.
Should this happen, ease open the cut with
wedges to relieve the strain on the blade. Do
not try to wrench the saw free.
2. Hold your D
handle (d) and the rear grip handle (c) to guide
the saw properly.
• Apply only a gentle pressure to the
tool and do not exert side pressure on
the saw blade.
• Avoid overloading.
WARNING: For applications where
mineral dust or hardwood is emitted due
to the work process the machine shall be
connected to a suitable dust extraction
system.
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
NOTICE: Do not use the saw for cutting
curves or pockets. Make sure the bar
end protrudes from the workpiece.
WALT power tool by the front
E