English - DeWalt D27112 Anweisungen

E N G L I S H
Support long workpieces using any convenient means such as saw-
horses or similar devices to keep the ends from dropping.
Consult your dealer for further information on the appropriate accessories.
Transporting (fi g. B)
• To transport the saw, lower the head and depress the lock down pin
(17).
• Lock the table (19) into lowest position. Lock the rail lock knob with
the saw head in the front position, lock the mitre arm in the far right
mitre angle, slide the fence (13) completely inward and lock the bevel
lever (15) with the saw head in the vertical position to make the tool
as compact as possible.
• Always use the hand indentations (26) shown in fi g. B to transport
the saw.
Always transport the machine in saw bench mode with the
upper blade guard fi tted. Never carry the machine by the
guard.
Maintenance
Your D WALT power tool has been designed to operate over a long
E
period of time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
• If the saw blade does not stop in less than 10 seconds after switching
off, have the machine serviced by an authorised D
agent.
Prior to maintenance always unplug the tool.
Cleaning
Keep the ventilation slots clear and regularly clean the housing with
a soft cloth.
• Regularly clean the table top.
Avoid the use of cleaners or lubricants to maintain the tool. In
particular spray and aerosol cleaners may chemically attack
the plastic lower guard.
Cleaning and maintaining the kerf plate (fi g. U)
Regularly clean the area below the kerf plate.
If the kerf plate is worn it must be replaced.
• Remove the screws (74) holding the kerf plate (8).
• Remove the kerf plate and clean the area below.
• Re-install the parts of the kerf plate and the screws.
• Tighten the screws hand-tight.
• To adjust the kerf plate, proceed as follows:
• Pull down the head until the blade just enters the saw kerf.
• Adjust each part of the kerf plate to fi t closely to the teeth of the blade.
• Tighten the screws.
L ubrication
This machine requires no additional lubrication. The bearings of the
motor are pre-lubricated and watertight.
• Avoid using oil or grease as this can cause clogging with sawdust
and chips and create problems.
• Clean the parts subject to accumulation of sawdust and chips
periodically with a dry brush.
36
Protecting the environment
Should you fi nd one day that your D
or if it is of no further use to you, do not dispose of it with household
waste. Make this product available for separate collection.
Local regulations may provide for separate collection of electrical
products from the household, at municipal waste sites or by the retailer
when you purchase a new product.
D WALT provides a facility for the collection and recycling of D
E
products once they have reached the end of their working life. To take
advantage of this service please return your product to any authorised
repair agent who will collect them on our behalf.
You can check the location of your nearest authorised repair agent by
contacting your local D
manual. Alternatively, a list of authorised D
WALT repair
E
details of our after-sales service and contacts are available on the
Internet at: www.2helpU.com
• 30 DAY NO RISK SATISFACTION GUARANTEE •
If you are not completely satisfi ed with the performance of your
D WALT machine, simply return it within 30 days, complete as
E
purchased, to the point of purchase, for a full refund or exchange.
Proof of purchase must be produced.
• ONE YEAR FREE SERVICE CONTRACT •
If you need maintenance or service for your D
12 months following purchase, it will be undertaken free of charge at
an authorized D
produced. Includes labour and spare parts for Power Tools.
Excludes accessories.
• ONE YEAR WARRANTY •
If your D
workmanship within 12 months from the date of purchase,
we guarantee to replace all defective parts free of charge or, at our
discretion, replace the unit free of charge provided that:
• The product has not been misused.
• Repairs have not been attempted by unauthorized persons.
• Proof of purchase date is produced.
This guarantee is offered as an extra benefi t and is additional to
consumers statutory rights.
For the location of your nearest authorized D
please use the appropriate telephone number on the back of this
manual. Alternatively, a list of authorized D
full details on our after-sales service are available on the Internet at
www.2helpU.com .
Separate collection. This product must not be disposed of
with normal household waste.
WALT product needs replacement,
E
Separate collection of used products and packaging allows
materials to be recycled and used again. Re-use of recycled
materials helps prevent environmental pollution and reduces
the demand for raw materials.
WALT offi ce at the address indicated in this
E
GUARANTEE
WALT repair agent. Proof of purchase must be
E
WALT product becomes defective due to faulty materials or
E
WALT
E
WALT repair agents and full
E
WALT machine, in the
E
WALT repair agent,
E
WALT repair agents and
E