Operation - DeWalt D27107 Originalanweisungen

WARNING: Use the 11 mm profile for ripping low workpieces
to allow access between the blade and the fence for the push
stick. The rear end of the fence should be level with the front of
the riving knife.
Mounting and adjusting the mitre fence (fi g. Q1 - Q4)
The mitre fence (D271052) is available as an option. The mitre fence (41) can
be used for mitre cutting when the machine is in saw bench mode (fi g. Q1).
• Loosen the clamp knob (115) and swing the guide bar (116) out (fi g. Q2).
Tighten the clamp knob.
• Slide the fence on the left side on the table (fi g. Q3).
• Loosen the lock knob (117).
• Place a square (82) against the fence (41) and the blade (76).
• If adjustment is required, proceed as follows:
• Loosen the nut (118) a few turns and turn the right angle adjustment
stop screw (119) (fi g. Q4) in or out until the fence is at 90° to the blade
as measured with the square (fi g. Q3).
• Tighten the knob (117).
• Check that the pointer (120) indicates zero on the scale (121).
Adjust if necessary.
Changing from saw bench to mitre saw mode (fi g. A3, E & M1)
• Remove the parallel fence (22), or the mitre fence, if fi tted (fi g. A3).
• Remove the upper blade guard (21).
• Replace the under-table guard (63) (fi g. E).
• Proceed as described in the section "Turning the sawhead and table
over".
• Slacken the riving knife clamp knob (97) and remove the riving knife (20),
while holding the blade guard (8) (fi g. M1).
• Lower the blade guard.
• Place the riving knife (20) in its storage position in the inside of the base
(fi g. A3).

OPERATION

Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of injury, turn unit off and
disconnect machine from power source before installing
and removing accessories, before adjusting or changing
set-ups or when making repairs. Be sure the trigger switch
is in the OFF position. An accidental start-up can cause injury.
WARNING:
• Ensure the material to be sawn is firmly secured in place.
• Apply only a gentle pressure to the tool and do not exert side
pressure on the saw blade.
• Avoid overloading.
Ensure the machine is placed to satisfy your ergonomic conditions in terms
of table height and stability. The machine site shall be chosen so that the
operator has a good overview and enough free surrounding space around
the machine that allows handling of the workpiece without any restrictions.
To reduce effects of vibration make sure the environment temperature is not
too cold, machine and accessory is well maintained and the workpiece size
is suitable for this machine.
Prior to operation:
• Install the appropriate saw blade. Do not use excessively worn blades.
The maximum rotation speed of the tool must not exceed that of the
saw blade.
• Do not attempt to cut excessively small pieces.
• Allow the blade to cut freely. Do not force.
• Allow the motor to reach full speed before cutting.
• Make sure all locking knobs and clamp handles are tight.
Switching on and off (fi g. A1, R1 - R3)
This machine has two independent switching systems. In mitre saw mode,
the trigger switch (11) is used (fi g. R1). In saw bench mode, the on/off
switch (1) is used (fi g. R2). Integrated in the switch box is a motor overload
protector with manual reset. In case of a power shut-off, proceed as
follows:
- Make sure the machine has been switched off.
- Press the reset button (142).
Mitre saw mode (fi g. R1)
A hole (122) is provided in the trigger for insertion of a padlock to lock the
switch.
• To run the tool, press the trigger switch (11).
• To stop the tool, release the switch.
Saw bench mode (fi g. R2 & R3)
The on/off switch offers multiple advantages:
- no-volt release function: should the power be shut off for some reason,
the switch has to be deliberately reactivated.
- extra safety: the hinged safety enclosure plate (123) can be locked by
passing a padlock through the holes (124 & 125). The plate also serves
as an "easy to locate" emergency stop button as pressure on the front
of the plate will depress the stop button.
• To switch the machine on, press the green start button (126).
• To switch the machine off, press the red stop button (127).
Locking the switches
• In order to avoid unauthorised use of the machine, lock both switches
using padlocks.
Basic saw cuts
Sawing in mitre saw mode
It is dangerous to operate without guarding. Guards must be in position
when sawing.
• Make sure that the under-table guard does not become clogged with
sawdust.
• Always clamp the workpiece when cutting non-ferrous metals.
General handling
- In the mitre saw mode, the sawhead is automatically locked in the
upper "park" position.
- Squeezing the guard release lever will unlock the sawhead. Moving the
sawhead down retracts the movable lower guard.
- Never seek to prevent the lower guard returning to its park position
when the cut is completed.
- The minimum length of offcut material is 10 mm.
- When cutting short material (min. 190 mm to the left or the right of the
blade), the use of the optional material clamp is recommended.
- When cutting UPVC sections, a supporting piece made out of timber
with a complementary profi le should be placed beneath the material
being cut to provide the correct level of support.
Vertical straight cross cut (fi g. S1)
• Loosen the mitre knob (79) and depress the mitre latch (80).
• Engage the mitre latch at the 0° position and tighten the mitre knob.
• Place the wood to be cut against the fence (7).
• Take hold of the operation handle (10) and press in the guard release
lever (9).
• Press the trigger switch (11) to start the motor.
E N G L I S H
45