Panasonic CQ-FX721N Bedienungsanleitung Seite 5

Radio
E
N
G
L
I
S [BAND]
(Auto preset memory/Set)
H
[MENU]
5
REM OTE
CH· C
1 2
PTY
[TUNE]] [TUNE[]
[P·SET}] [P·SET{] (Preset station/Select)
[SOURCE]
[1] to [6] (Preset station)
[SEL] (Menu)
[BAND] (Auto preset memory/Set)
[}] [{]
(Preset station/Select)
Mono/Local Selection
q Press [MENU] / [SEL] during radio (FM or AM) mode.
w Press [P·SET}] or [P·SET{] / [}] or [{] to select MONO or LOCAL.
(in AM mode, only LOCAL can be selected.)
e Press [BAND] to switch on or off in turn.
MONO ON : Noise is significantly decreased when weak signals are received
from an FM broadcast station.
LOCAL ON : In seek tuning, only strong stations are detected.
LOCAL OFF: Relatively weak stations are picked up.
Notes:
¡If no keys have been pressed for more than 15 seconds, the display returns to the previous one after changing to the
menu display.
¡Press [DISP] to return to the regular mode.
8
CQ-FX721N
Radio Mode Display
Band
Stereo Indicator
[SOURCE]
Note : The stereo indicator lights during
reception of an FM stereo broadcast.
1
Radio Mode
Press [SOURCE] to select the radio
mode.
Band
2
Press [BAND] .
FM1
FM2
FM3
[]] [[] (Tune)
AM (LW/MW)
3
Tuning
[TUNE[] / [[] : Up
[TUNE]] / []] : Down
Press and hold [TUNE[] or [TUNE]] /
[[] or []] for more than 0.5 seconds,
then release. Seeking will start.
FM Menu Display
AM Menu Display
One-touch Selection of a Preset Station
Up to 6 stations can be stored in each of the FM1, FM2, FM3 and AM (LW/MW) band selections.
Frequency
Manual Preset
Memory
Manually save a station in
the preset memory.
Auto Preset
Memory
Automatically save strong
stations in the preset
memory.
Note : New stations are overwritten on existing saved stations after following this procedure.
Preset Station
Calling
Select a band and frequency (step q , w and e on the previous page)
q Press and hold [P·SET}] or [P·SET{] / [}] or [{] for more
than 2 seconds until the preset number blinks.
w Press [P·SET}] or [P·SET{] / [}] or [{] to select a preset
number.
e Press and hold [P·SET}] or [P·SET{] / [}] or [{] for more
than 2 seconds to memorize.
The display blinks once, and a receiving
station is saved in the memory.
Note : Frequency setting can be performed even after selecting a preset
number.
Entering numbers directly from the remote control
Select a band and frequency (step q , w and e on the previous page)
Press and hold [1] to [6] on the remote control for more than 2 seconds.
Select a band (step q , w on the previous page)
Press and hold [BAND] for more than
Scanning
2 seconds.
¡The 6 strongest available stations will be automatically saved in the memory
under preset numbers 1 to 6.
¡Once set, the preset stations are sequentially scanned for 5 seconds each.
¡To stop the scanning, press [P·SET}] or [P·SET{] / [}] or [{].
(Pressing [1] to [6] on the remote control also can stop the scanning.)
Select a band (step q , w on the previous page)
Press [P·SET}] or [P·SET{] / [}] or [{] to select the preset number
for tuning in the preset station.
Entering numbers directly from the remote control
Press [1] to [6] on the remote control.
CQ-FX721N
E
N
G
L
I
S
H
6
9